Salut.
Alors, lorsque j'essaie d’accéder à mon disque, j'ai le message suivant...
Message d'erreur non géré : Erreur lors de l'obtention des informations du fichier « /media/usb0 » : Noeud final de transport n'est pas connecté
Ensuite, lorsque je fais dmesg | tail -n 40...
ludo@ubuntu:~$ dmesg | tail -n 40
[ 8636.049294] rtc_cmos 00:01: System wakeup disabled by ACPI
[ 8636.109570] xhci_hcd 0000:00:14.0: port 1 resume PLC timeout
[ 8636.136690] r8169 0000:0e:00.0 enp14s0: link down
[ 8636.334697] usb 3-2: reset full-speed USB device number 2 using xhci_hcd
[ 8636.370443] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 8636.374119] ata5.00: configured for UDMA/133
[ 8636.464925] PM: resume of devices complete after 437.050 msecs
[ 8636.465245] PM: Finishing wakeup.
[ 8636.465248] Restarting tasks ... done.
[ 8636.725799] psmouse serio1: synaptics: queried max coordinates: x [..5682], y [..4770]
[ 8636.752653] psmouse serio1: synaptics: queried min coordinates: x [1260..], y [1082..]
[ 8637.944441] r8169 0000:0e:00.0 enp14s0: link up
[ 8638.994345] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 8639.251000] ata1.00: configured for UDMA/133
[ 8641.525493] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[ 8641.543484] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[ 8641.545583] IPv6: ADDRCONF(NETDEV_UP): enp14s0: link is not ready
[ 8641.644421] r8169 0000:0e:00.0 enp14s0: link down
[ 8641.644481] r8169 0000:0e:00.0 enp14s0: link down
[ 8641.644523] IPv6: ADDRCONF(NETDEV_UP): enp14s0: link is not ready
[ 8641.691731] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[ 8643.275904] r8169 0000:0e:00.0 enp14s0: link up
[ 8643.275918] IPv6: ADDRCONF(NETDEV_CHANGE): enp14s0: link becomes ready
[ 8679.232766] perf interrupt took too long (2511 > 2500), lowering kernel.perf_event_max_sample_rate to 50000
[ 8762.708652] usb 2-1.4: new high-speed USB device number 4 using ehci-pci
[ 8762.803993] usb 2-1.4: New USB device found, idVendor=0480, idProduct=0101
[ 8762.804001] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8762.804005] usb 2-1.4: Product: External USB 3.0
[ 8762.804008] usb 2-1.4: Manufacturer: TOSHIBA
[ 8762.804011] usb 2-1.4: SerialNumber: 20151115007530F
[ 8762.804528] usb-storage 2-1.4:1.0: USB Mass Storage device detected
[ 8762.806180] scsi host6: usb-storage 2-1.4:1.0
[ 8765.722980] scsi 6:0:0:0: Direct-Access TOSHIBA External USB 3.0 5438 PQ: 0 ANSI: 6
[ 8765.726288] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 8765.728270] sd 6:0:0:0: [sdb] 1953525164 512-byte logical blocks: (1.00 TB/932 GiB)
[ 8765.729224] sd 6:0:0:0: [sdb] Write Protect is off
[ 8765.729232] sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 8765.730035] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8765.747709] sdb: sdb1
[ 8765.751637] sd 6:0:0:0: [sdb] Attached SCSI disk
Puis avec la commande
cat /etc/fstab
ludo@ubuntu:~$ cat /etc/fstab
# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a
# device; this may be used with UUID= as a more robust way to name devices
# that works even if disks are added and removed. See fstab(5).
#
# <file system> <mount point> <type> <options> <dump> <pass>
# / was on /dev/sda1 during installation
UUID=541ec569-dcf8-4e69-9113-3dd38414ec9f / ext4 errors=remount-ro 0 1
# swap was on /dev/sda5 during installation
UUID=8f3533ea-edbb-46e0-b000-1836955f81dd none swap sw 0 0
