Ce site est optimisé pour être consulté depuis un navigateur moderne dans lequel JavaScript est activé.

DD externe ne se monte pas

toinou1988

Bonjour,

Je m'excuse par avance, j'ai très peu de compétences en informatique, donc je risque de poser des question assez basiques.

Je viens de changer d'ordinateur et j'ai un problème : j'utilise un disque dur externe pour faire des sauvegardes avec deja-dup. Mon problème est que lorsque je branche ce disque dur sur mon nouvel ordinateur (celui-ci et l'ancien sont en Ubuntu), il ne se monte plus, alors que cela avait fonctionné la première fois. Par contre, il fonctionne parfaitement sur mon ancien ordinateur.
Je précise que je m'en suis servi pour passer des fichiers d'un ordinateur à l'autre, donc il a été connecté aux deux.

Quelqu'un aurait-il une idée ?

LeJediGris

Salut,

DD externe débranché, rebranches-le et donne le retour de

dmesg | tail -30

A+

toinou1988

antoine@antoine-N13xWU:~$ dmesg | tail -30
[    6.688188] Bluetooth: hci0: Device booted in 11793 usecs
[    6.688418] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-12-16.ddc
[    6.690097] Bluetooth: hci0: Applying Intel DDC parameters completed
[    6.760906] IPv6: ADDRCONF(NETDEV_UP): enp58s0f1: link is not ready
[    6.782206] r8169 0000:3a:00.1 enp58s0f1: link down
[    6.782280] IPv6: ADDRCONF(NETDEV_UP): enp58s0f1: link is not ready
[    6.785632] IPv6: ADDRCONF(NETDEV_UP): wlp59s0: link is not ready
[    6.987858] IPv6: ADDRCONF(NETDEV_UP): wlp59s0: link is not ready
[    7.146429] IPv6: ADDRCONF(NETDEV_UP): wlp59s0: link is not ready
[    7.245342] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input18
[    7.245589] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input19
[    7.245682] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input20
[    7.245762] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input21
[    7.245841] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input22
[    7.245922] input: HDA Intel PCH HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input23
[    7.245999] input: HDA Intel PCH HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input24
[   13.602342] wlp59s0: authenticate with a8:d3:f7:a0:91:92
[   13.610870] wlp59s0: send auth to a8:d3:f7:a0:91:92 (try 1/3)
[   13.616462] wlp59s0: authenticated
[   13.624043] wlp59s0: associate with a8:d3:f7:a0:91:92 (try 1/3)
[   13.625460] wlp59s0: RX AssocResp from a8:d3:f7:a0:91:92 (capab=0x11 status=0 aid=1)
[   13.627496] wlp59s0: associated
[   13.627531] IPv6: ADDRCONF(NETDEV_CHANGE): wlp59s0: link becomes ready
[   13.714340] wlp59s0: Limiting TX power to 23 (23 - 0) dBm as advertised by a8:d3:f7:a0:91:92
[   14.680811] Bluetooth: RFCOMM TTY layer initialized
[   14.680827] Bluetooth: RFCOMM socket layer initialized
[   14.680838] Bluetooth: RFCOMM ver 1.11
[   15.384064] rfkill: input handler disabled
[   72.634671] show_signal_msg: 32 callbacks suppressed
[   72.634677] ntfs-config[2204]: segfault at 18 ip 00007f0348d9fec9 sp 00007ffd39c22c50 error 4 in libgdk-x11-2.0.so.0.2400.31[7f0348d2f000+af000]

LeJediGris

Tu avais rebranché le DD externe avant le dmesg ????
Je ne vois pas de signe de branchement !! essaye avec une autre prise USB sur ton nouveau PC.

A+

Nasman

Problème d'alimentation du disque externe ?

moko138

[   72.634677] ntfs-config[2204]: segfault at 18 ip 00007f0348d9fec9 sp 00007ffd39c22c50 error 4 in libgdk-x11-2.0.so.0.2400.31[7f0348d2f000+af000]

toinou1988

Oui, il était bien branché, une diode s'allume et je l'entends tourner.

Sur un autre USB :

antoine@antoine-N13xWU:~$ dmesg | tail -30
[    6.688188] Bluetooth: hci0: Device booted in 11793 usecs
[    6.688418] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-12-16.ddc
[    6.690097] Bluetooth: hci0: Applying Intel DDC parameters completed
[    6.760906] IPv6: ADDRCONF(NETDEV_UP): enp58s0f1: link is not ready
[    6.782206] r8169 0000:3a:00.1 enp58s0f1: link down
[    6.782280] IPv6: ADDRCONF(NETDEV_UP): enp58s0f1: link is not ready
[    6.785632] IPv6: ADDRCONF(NETDEV_UP): wlp59s0: link is not ready
[    6.987858] IPv6: ADDRCONF(NETDEV_UP): wlp59s0: link is not ready
[    7.146429] IPv6: ADDRCONF(NETDEV_UP): wlp59s0: link is not ready
[    7.245342] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input18
[    7.245589] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input19
[    7.245682] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input20
[    7.245762] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input21
[    7.245841] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input22
[    7.245922] input: HDA Intel PCH HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input23
[    7.245999] input: HDA Intel PCH HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input24
[   13.602342] wlp59s0: authenticate with a8:d3:f7:a0:91:92
[   13.610870] wlp59s0: send auth to a8:d3:f7:a0:91:92 (try 1/3)
[   13.616462] wlp59s0: authenticated
[   13.624043] wlp59s0: associate with a8:d3:f7:a0:91:92 (try 1/3)
[   13.625460] wlp59s0: RX AssocResp from a8:d3:f7:a0:91:92 (capab=0x11 status=0 aid=1)
[   13.627496] wlp59s0: associated
[   13.627531] IPv6: ADDRCONF(NETDEV_CHANGE): wlp59s0: link becomes ready
[   13.714340] wlp59s0: Limiting TX power to 23 (23 - 0) dBm as advertised by a8:d3:f7:a0:91:92
[   14.680811] Bluetooth: RFCOMM TTY layer initialized
[   14.680827] Bluetooth: RFCOMM socket layer initialized
[   14.680838] Bluetooth: RFCOMM ver 1.11
[   15.384064] rfkill: input handler disabled
[   72.634671] show_signal_msg: 32 callbacks suppressed
[   72.634677] ntfs-config[2204]: segfault at 18 ip 00007f0348d9fec9 sp 00007ffd39c22c50 error 4 in libgdk-x11-2.0.so.0.2400.31[7f0348d2f000+af000]

LeJediGris

moko138 a écrit

[   72.634677] ntfs-config[2204]: segfault at 18 ip 00007f0348d9fec9 sp 00007ffd39c22c50 error 4 in libgdk-x11-2.0.so.0.2400.31[7f0348d2f000+af000]

Oui je l'ai vu aussi, ce qui est bizarre c'est que l'on devrait au moins avoir quelques lignes d'abord du driver HCI...avant l'activation de ntfs !!

Donc soit alim, soit connecteur USB 3 vs USB 2 etc...

A+

toinou1988

Et j'ai essayé les deux USB avec une clé USB, ça semble marcher...
Par contre, je viens d'aller essayer le DD sur l'ordinateur de mon voisin, en Windows, il n'est pas non plus détecté.

moko138

toinou1988,
tu as collé une deuxième fois le retour précédent, sans trace de branchement du 2ème DDE.

toinou1988

Il ne me semble pas mais dans le doute, je viens de le refaire.

antoine@antoine-N13xWU:~$ dmesg | tail -30
[    6.688188] Bluetooth: hci0: Device booted in 11793 usecs
[    6.688418] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-12-16.ddc
[    6.690097] Bluetooth: hci0: Applying Intel DDC parameters completed
[    6.760906] IPv6: ADDRCONF(NETDEV_UP): enp58s0f1: link is not ready
[    6.782206] r8169 0000:3a:00.1 enp58s0f1: link down
[    6.782280] IPv6: ADDRCONF(NETDEV_UP): enp58s0f1: link is not ready
[    6.785632] IPv6: ADDRCONF(NETDEV_UP): wlp59s0: link is not ready
[    6.987858] IPv6: ADDRCONF(NETDEV_UP): wlp59s0: link is not ready
[    7.146429] IPv6: ADDRCONF(NETDEV_UP): wlp59s0: link is not ready
[    7.245342] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input18
[    7.245589] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input19
[    7.245682] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input20
[    7.245762] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input21
[    7.245841] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input22
[    7.245922] input: HDA Intel PCH HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input23
[    7.245999] input: HDA Intel PCH HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input24
[   13.602342] wlp59s0: authenticate with a8:d3:f7:a0:91:92
[   13.610870] wlp59s0: send auth to a8:d3:f7:a0:91:92 (try 1/3)
[   13.616462] wlp59s0: authenticated
[   13.624043] wlp59s0: associate with a8:d3:f7:a0:91:92 (try 1/3)
[   13.625460] wlp59s0: RX AssocResp from a8:d3:f7:a0:91:92 (capab=0x11 status=0 aid=1)
[   13.627496] wlp59s0: associated
[   13.627531] IPv6: ADDRCONF(NETDEV_CHANGE): wlp59s0: link becomes ready
[   13.714340] wlp59s0: Limiting TX power to 23 (23 - 0) dBm as advertised by a8:d3:f7:a0:91:92
[   14.680811] Bluetooth: RFCOMM TTY layer initialized
[   14.680827] Bluetooth: RFCOMM socket layer initialized
[   14.680838] Bluetooth: RFCOMM ver 1.11
[   15.384064] rfkill: input handler disabled
[   72.634671] show_signal_msg: 32 callbacks suppressed
[   72.634677] ntfs-config[2204]: segfault at 18 ip 00007f0348d9fec9 sp 00007ffd39c22c50 error 4 in libgdk-x11-2.0.so.0.2400.31[7f0348d2f000+af000]

toinou1988

J'ai lancé lsusb pour vérifier mes ports USB

Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 003: ID 8087:0a2b Intel Corp. 
Bus 001 Device 002: ID 064e:3410 Suyin Corp. 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Je suis supposé avoir deux ports USB 3 et un 3.1. Est-ce que ça vous semble correspondre ?

toinou1988

J'ai relancé

dmesg | tail -30

avec une clé usb qui fonctionne :

antoine@antoine-N13xWU:~$ dmesg | tail -30
[   13.625460] wlp59s0: RX AssocResp from a8:d3:f7:a0:91:92 (capab=0x11 status=0 aid=1)
[   13.627496] wlp59s0: associated
[   13.627531] IPv6: ADDRCONF(NETDEV_CHANGE): wlp59s0: link becomes ready
[   13.714340] wlp59s0: Limiting TX power to 23 (23 - 0) dBm as advertised by a8:d3:f7:a0:91:92
[   14.680811] Bluetooth: RFCOMM TTY layer initialized
[   14.680827] Bluetooth: RFCOMM socket layer initialized
[   14.680838] Bluetooth: RFCOMM ver 1.11
[   15.384064] rfkill: input handler disabled
[   72.634671] show_signal_msg: 32 callbacks suppressed
[   72.634677] ntfs-config[2204]: segfault at 18 ip 00007f0348d9fec9 sp 00007ffd39c22c50 error 4 in libgdk-x11-2.0.so.0.2400.31[7f0348d2f000+af000]
[ 2541.872607] usb 1-1: new high-speed USB device number 4 using xhci_hcd
[ 2542.013477] usb 1-1: New USB device found, idVendor=0718, idProduct=0710
[ 2542.013485] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2542.013490] usb 1-1: Product: TF10
[ 2542.013494] usb 1-1: Manufacturer: TDK LoR
[ 2542.013498] usb 1-1: SerialNumber: 1258000000000A9F
[ 2542.034806] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 2542.034875] scsi host1: usb-storage 1-1:1.0
[ 2542.034933] usbcore: registered new interface driver usb-storage
[ 2542.036128] usbcore: registered new interface driver uas
[ 2543.061226] scsi 1:0:0:0: Direct-Access     TDK LoR  TF10             1.00 PQ: 0 ANSI: 2
[ 2543.062051] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 2543.062585] sd 1:0:0:0: [sdb] 15669248 512-byte logical blocks: (8.02 GB/7.47 GiB)
[ 2543.062883] sd 1:0:0:0: [sdb] Write Protect is off
[ 2543.062891] sd 1:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 2543.063144] sd 1:0:0:0: [sdb] No Caching mode page found
[ 2543.063158] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 2543.066203]  sdb: sdb1
[ 2543.067901] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 2543.622479] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.

Est-ce qu'il faudrait que j'essaie la même opération avec le DD sur l'ordinateur avec lequel il fonctionne ?

moko138

Et j'ai essayé les deux USB avec une clé USB, ça semble marcher...

Clairement non !

LeJediGris a écrit Oui je l'ai vu aussi, ce qui est bizarre c'est que l'on devrait au moins avoir quelques lignes d'abord du driver HCI...avant l'activation de ntfs !!

Très juste.
De toute façon, pour causer une mauvaise reconnaissance des branchements usb ET une segfault,
il y a un problème (et probablement plus d'un) dans le système installé sur le disque interne. Et soit sur la carte-mère soit sur le disque interne.
- -

toinou1988,
donne

dmesg | tail -1

aussitôt après, branche une clef usb qui marche,
attends 30 secondes
et montre

lsusb; echo; lsusb -t

et aussitôt après,

dmesg | grep -Evi "80211|dhcp|ipv6|network|ufw|wlan|wlp5" | tail -35

.
Puis même cycle avec le DDE qui foire,
Merci !

/!\ Ne cherche surtout pas à retaper ces lignes ! Utilise :
- un triple clic gauche sur une ligne pour la sélectionner tout entière et la copier,
- un clic milieu pour la coller.

toinou1988

Avec la clé USB

antoine@antoine-N13xWU:~$ dmesg | tail -1
[ 2708.264408] usb 1-1: USB disconnect, device number 4
antoine@antoine-N13xWU:~$ lsusb; echo; lsusb -t
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 005: ID 0718:0710 Imation Corp. 
Bus 001 Device 003: ID 8087:0a2b Intel Corp. 
Bus 001 Device 002: ID 064e:3410 Suyin Corp. 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/12p, 480M
    |__ Port 4: Dev 2, If 1, Class=Video, Driver=uvcvideo, 480M
    |__ Port 4: Dev 2, If 0, Class=Video, Driver=uvcvideo, 480M
    |__ Port 5: Dev 3, If 1, Class=Wireless, Driver=btusb, 12M
    |__ Port 5: Dev 3, If 0, Class=Wireless, Driver=btusb, 12M
    |__ Port 7: Dev 5, If 0, Class=Mass Storage, Driver=usb-storage, 480M
antoine@antoine-N13xWU:~$ dmesg | grep -Evi "80211|dhcp|ipv6|network|ufw|wlan|wlp5" | tail -35
[ 2542.013494] usb 1-1: Manufacturer: TDK LoR
[ 2542.013498] usb 1-1: SerialNumber: 1258000000000A9F
[ 2542.034806] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 2542.034875] scsi host1: usb-storage 1-1:1.0
[ 2542.034933] usbcore: registered new interface driver usb-storage
[ 2542.036128] usbcore: registered new interface driver uas
[ 2543.061226] scsi 1:0:0:0: Direct-Access     TDK LoR  TF10             1.00 PQ: 0 ANSI: 2
[ 2543.062051] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 2543.062585] sd 1:0:0:0: [sdb] 15669248 512-byte logical blocks: (8.02 GB/7.47 GiB)
[ 2543.062883] sd 1:0:0:0: [sdb] Write Protect is off
[ 2543.062891] sd 1:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 2543.063144] sd 1:0:0:0: [sdb] No Caching mode page found
[ 2543.063158] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 2543.066203]  sdb: sdb1
[ 2543.067901] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 2543.622479] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 2708.264408] usb 1-1: USB disconnect, device number 4
[ 3443.772238] usb 1-7: new high-speed USB device number 5 using xhci_hcd
[ 3443.912852] usb 1-7: New USB device found, idVendor=0718, idProduct=0710
[ 3443.912859] usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3443.912864] usb 1-7: Product: TF10
[ 3443.912869] usb 1-7: Manufacturer: TDK LoR
[ 3443.912873] usb 1-7: SerialNumber: 1258000000000A9F
[ 3443.913588] usb-storage 1-7:1.0: USB Mass Storage device detected
[ 3443.913972] scsi host1: usb-storage 1-7:1.0
[ 3444.916581] scsi 1:0:0:0: Direct-Access     TDK LoR  TF10             1.00 PQ: 0 ANSI: 2
[ 3444.917415] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 3444.917899] sd 1:0:0:0: [sdb] 15669248 512-byte logical blocks: (8.02 GB/7.47 GiB)
[ 3444.918135] sd 1:0:0:0: [sdb] Write Protect is off
[ 3444.918142] sd 1:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 3444.918368] sd 1:0:0:0: [sdb] No Caching mode page found
[ 3444.918381] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 3444.921326]  sdb: sdb1
[ 3444.922408] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 3445.384625] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.

Avec le DDE

antoine@antoine-N13xWU:~$ dmesg | tail -1
[ 3600.375324] usb 1-7: USB disconnect, device number 5
antoine@antoine-N13xWU:~$ lsusb; echo; lsusb -tBus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 003: ID 8087:0a2b Intel Corp. 
Bus 001 Device 002: ID 064e:3410 Suyin Corp. 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/12p, 480M
    |__ Port 4: Dev 2, If 1, Class=Video, Driver=uvcvideo, 480M
    |__ Port 4: Dev 2, If 0, Class=Video, Driver=uvcvideo, 480M
    |__ Port 5: Dev 3, If 0, Class=Wireless, Driver=btusb, 12M
    |__ Port 5: Dev 3, If 1, Class=Wireless, Driver=btusb, 12M
antoine@antoine-N13xWU:~$ dmesg | grep -Evi "80211|dhcp|ipv6|network|ufw|wlan|wlp5" | tail -35
[ 2542.013498] usb 1-1: SerialNumber: 1258000000000A9F
[ 2542.034806] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 2542.034875] scsi host1: usb-storage 1-1:1.0
[ 2542.034933] usbcore: registered new interface driver usb-storage
[ 2542.036128] usbcore: registered new interface driver uas
[ 2543.061226] scsi 1:0:0:0: Direct-Access     TDK LoR  TF10             1.00 PQ: 0 ANSI: 2
[ 2543.062051] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 2543.062585] sd 1:0:0:0: [sdb] 15669248 512-byte logical blocks: (8.02 GB/7.47 GiB)
[ 2543.062883] sd 1:0:0:0: [sdb] Write Protect is off
[ 2543.062891] sd 1:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 2543.063144] sd 1:0:0:0: [sdb] No Caching mode page found
[ 2543.063158] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 2543.066203]  sdb: sdb1
[ 2543.067901] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 2543.622479] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 2708.264408] usb 1-1: USB disconnect, device number 4
[ 3443.772238] usb 1-7: new high-speed USB device number 5 using xhci_hcd
[ 3443.912852] usb 1-7: New USB device found, idVendor=0718, idProduct=0710
[ 3443.912859] usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3443.912864] usb 1-7: Product: TF10
[ 3443.912869] usb 1-7: Manufacturer: TDK LoR
[ 3443.912873] usb 1-7: SerialNumber: 1258000000000A9F
[ 3443.913588] usb-storage 1-7:1.0: USB Mass Storage device detected
[ 3443.913972] scsi host1: usb-storage 1-7:1.0
[ 3444.916581] scsi 1:0:0:0: Direct-Access     TDK LoR  TF10             1.00 PQ: 0 ANSI: 2
[ 3444.917415] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 3444.917899] sd 1:0:0:0: [sdb] 15669248 512-byte logical blocks: (8.02 GB/7.47 GiB)
[ 3444.918135] sd 1:0:0:0: [sdb] Write Protect is off
[ 3444.918142] sd 1:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 3444.918368] sd 1:0:0:0: [sdb] No Caching mode page found
[ 3444.918381] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 3444.921326]  sdb: sdb1
[ 3444.922408] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 3445.384625] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 3600.375324] usb 1-7: USB disconnect, device number 5

Etant donné que cet ordinateur est neuf (acheté hier). Devrais-je aller voir avec l'entreprise qui me l'a vendu ?

moko138

Le boîtier du DDE n'est pas reconnu. Je dis bien le boîtier.

Essaie aussi avec un autre câble usb, même vieux (pas besoin d'usb3).

moko138

Etant donné que cet ordinateur est neuf (acheté hier)

a) Installer l'utilitaire pour contrôler le disque (interne) :

sudo apt-get install --no-install-recommends smartmontools

- -
b) Lire les données SMART :
faire sans ajouter de chiffre :

sudo smartctl -s on -a /dev/sda

et en donner le retour complet et entre balises-code.

toinou1988

J'ai eu un peu de difficulté à trouver un câble du même modèle mais ça semble marcher.

C'est plutôt vicieux comme histoire, je dois dire. J'ai déjà eu un problème similaire dans une installation hifi, j'ai mis six mois à trouver.

Merci beaucoup à ceux qui ont aidé, en particulier à moko138 !

moko138

[center]Attention, ton fil n'est pas encore résolu ![/center]

1) Réponds au #17.

2) La segfault est encore pendante et n'a rien à voir avec le problème de câble.

3) Et sur

[ 2543.622479] FAT-fs (sdb1): Volume was not properly unmounted.

- Cette clef usb à vérifier depuis un windows quelconque.
- Prends l'habitude "d'éjecter en toute sécurité" avant de débrancher tes périphériques usb, même si tu comptes éteindre windows juste après !