Ce site est optimisé pour être consulté depuis un navigateur moderne dans lequel JavaScript est activé.

Clé USB MP3 Samsung YP-U6 pas reconnue

Samsara035

Bonjour,
Ce lecteur MP3 n'est pas reconnu sur Ubuntu 18-04-1 LTS, Il fonctionnait très bien sur Ubuntu 16-04...
Merci de votre aide.

moko138

Applique ./viewtopic.php?id=2031501 "[Tuto] Ma clef (ou autre support amovible) ne monte pas ou mal"

Samsara035

Merci pour la réponse.

Retour de la commande comme demandé:

nsfs on /run/snapd/ns/p7zip-desktop.mnt type nsfs (rw)

Bus 002 Device 002: ID 8087:8000 Intel Corp. 
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 13d3:3394 IMC Networks Bluetooth
Bus 001 Device 002: ID 8087:8008 Intel Corp. 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

/:  Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/4p, 5000M
/:  Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/14p, 480M
/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/2p, 480M
    |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/8p, 480M
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/2p, 480M
    |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/6p, 480M
        |__ Port 3: Dev 3, If 0, Class=Wireless, Driver=btusb, 12M
        |__ Port 3: Dev 3, If 1, Class=Wireless, Driver=btusb, 12M

[ 6460.717335] usb 1-1.2: USB disconnect, device number 88
[ 6469.008211] usb 1-1.2: new high-speed USB device number 89 using ehci-pci
[ 6469.118215] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6469.118221] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6469.118225] usb 1-1.2: Product: YP-U6
[ 6469.118228] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6469.118231] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6469.119066] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6469.119937] scsi host5: usb-storage 1-1.2:1.0
[ 6469.299688] usb 1-1.2: USB disconnect, device number 89
[ 6469.524232] usb 1-1.2: new high-speed USB device number 90 using ehci-pci
[ 6469.634095] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6469.634100] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6469.634104] usb 1-1.2: Product: YP-U6
[ 6469.634107] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6469.634110] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6469.634805] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6469.635061] scsi host5: usb-storage 1-1.2:1.0
[ 6469.811492] usb 1-1.2: USB disconnect, device number 90
[ 6470.032216] usb 1-1.2: new high-speed USB device number 91 using ehci-pci
[ 6470.152735] usb 1-1.2: device descriptor read/all, error -71
[ 6470.656171] usb 1-1.2: new high-speed USB device number 92 using ehci-pci
[ 6471.160127] usb 1-1.2: device not accepting address 92, error -71
[ 6471.160280] usb 1-1-port2: attempt power cycle
[ 6471.764063] usb 1-1.2: new high-speed USB device number 93 using ehci-pci
[ 6472.188019] usb 1-1.2: device not accepting address 93, error -71
[ 6472.476023] usb 1-1.2: new high-speed USB device number 94 using ehci-pci
[ 6472.506102] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6472.506107] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6472.506110] usb 1-1.2: Product: YP-U6
[ 6472.506112] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6472.506115] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6472.506922] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6472.507373] scsi host5: usb-storage 1-1.2:1.0
[ 6472.627515] usb 1-1.2: USB disconnect, device number 94
[ 6473.475965] usb 1-1.2: new high-speed USB device number 95 using ehci-pci
[ 6473.585859] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6473.585866] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6473.585870] usb 1-1.2: Product: YP-U6
[ 6473.585874] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6473.585878] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6473.586966] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6473.588851] scsi host5: usb-storage 1-1.2:1.0
[ 6474.419717] usb 1-1.2: USB disconnect, device number 95
[ 6474.663877] usb 1-1.2: new high-speed USB device number 96 using ehci-pci
[ 6474.773740] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6474.773746] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6474.773750] usb 1-1.2: Product: YP-U6
[ 6474.773753] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6474.773757] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6474.774410] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6474.774694] scsi host5: usb-storage 1-1.2:1.0
[ 6474.931718] usb 1-1.2: USB disconnect, device number 96
[ 6475.175827] usb 1-1.2: new high-speed USB device number 97 using ehci-pci
[ 6475.285734] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6475.285739] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6475.285742] usb 1-1.2: Product: YP-U6
[ 6475.285745] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6475.285748] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6475.286420] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6475.287170] scsi host5: usb-storage 1-1.2:1.0
[ 6475.443367] usb 1-1.2: USB disconnect, device number 97
[ 6475.667806] usb 1-1.2: new high-speed USB device number 98 using ehci-pci
[ 6475.777746] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6475.777752] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6475.777756] usb 1-1.2: Product: YP-U6
[ 6475.777760] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6475.777764] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6475.778719] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6475.779435] scsi host5: usb-storage 1-1.2:1.0
[ 6475.955719] usb 1-1.2: USB disconnect, device number 98
[ 6476.387758] usb 1-1.2: new high-speed USB device number 99 using ehci-pci
[ 6476.497617] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6476.497623] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6476.497627] usb 1-1.2: Product: YP-U6
[ 6476.497630] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6476.497634] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6476.498305] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6476.500052] scsi host5: usb-storage 1-1.2:1.0
[ 6476.723727] usb 1-1.2: USB disconnect, device number 99
[ 6476.947723] usb 1-1.2: new high-speed USB device number 100 using ehci-pci
[ 6477.455660] usb 1-1.2: device descriptor read/64, error -71
[ 6478.067619] usb 1-1.2: device not accepting address 100, error -71
[ 6478.355610] usb 1-1.2: new high-speed USB device number 101 using ehci-pci
[ 6478.465491] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6478.465497] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6478.465501] usb 1-1.2: Product: YP-U6
[ 6478.465505] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6478.465508] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6478.466602] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6478.467256] scsi host5: usb-storage 1-1.2:1.0
[ 6478.515520] usb 1-1.2: USB disconnect, device number 101
[ 6478.755543] usb 1-1.2: new high-speed USB device number 102 using ehci-pci
[ 6479.259536] usb 1-1.2: device not accepting address 102, error -71
[ 6479.547516] usb 1-1.2: new high-speed USB device number 103 using ehci-pci
[ 6479.657382] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6479.657388] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6479.657393] usb 1-1.2: Product: YP-U6
[ 6479.657397] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6479.657400] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6479.658351] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6479.660442] scsi host5: usb-storage 1-1.2:1.0
[ 6479.661260] usb 1-1.2: USB disconnect, device number 103
[ 6480.147477] usb 1-1.2: new high-speed USB device number 104 using ehci-pci
[ 6480.447428] usb 1-1.2: device descriptor read/64, error -71
[ 6481.431321] usb 1-1.2: device descriptor read/64, error -71
[ 6481.619321] usb 1-1.2: new high-speed USB device number 105 using ehci-pci
[ 6481.739792] usb 1-1.2: device descriptor read/all, error -71
[ 6481.747227] usb 1-1-port2: attempt power cycle
[ 6482.351278] usb 1-1.2: new high-speed USB device number 106 using ehci-pci
[ 6482.381258] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6482.381262] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6482.381264] usb 1-1.2: Product: YP-U6
[ 6482.381267] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6482.381269] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6482.381955] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6482.382409] scsi host5: usb-storage 1-1.2:1.0
[ 6483.379546] usb 1-1.2: USB disconnect, device number 106
[ 6483.603104] usb 1-1.2: new high-speed USB device number 107 using ehci-pci
[ 6483.713141] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6483.713145] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6483.713148] usb 1-1.2: Product: YP-U6
[ 6483.713151] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6483.713154] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6483.713838] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6483.714362] scsi host5: usb-storage 1-1.2:1.0
[ 6483.891433] usb 1-1.2: USB disconnect, device number 107
[ 6484.131157] usb 1-1.2: new high-speed USB device number 108 using ehci-pci
[ 6484.635117] usb 1-1.2: device not accepting address 108, error -71
[ 6484.922986] usb 1-1.2: new high-speed USB device number 109 using ehci-pci
[ 6485.639026] usb 1-1.2: device descriptor read/64, error -71
[ 6486.046963] usb 1-1.2: device descriptor read/64, error -71
[ 6486.155074] usb 1-1-port2: attempt power cycle
[ 6486.758940] usb 1-1.2: new high-speed USB device number 110 using ehci-pci
[ 6486.788906] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6486.788912] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6486.788916] usb 1-1.2: Product: YP-U6
[ 6486.788919] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6486.788923] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6486.789864] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6486.790087] scsi host5: usb-storage 1-1.2:1.0
[ 6486.963435] usb 1-1.2: USB disconnect, device number 110
[ 6487.186907] usb 1-1.2: new high-speed USB device number 111 using ehci-pci
[ 6487.296789] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6487.296796] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6487.296800] usb 1-1.2: Product: YP-U6
[ 6487.296804] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6487.296808] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6487.297767] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6487.298563] scsi host5: usb-storage 1-1.2:1.0
[ 6487.731437] usb 1-1.2: USB disconnect, device number 111
[ 6487.958840] usb 1-1.2: new high-speed USB device number 112 using ehci-pci
[ 6488.258806] usb 1-1.2: device descriptor read/64, error -71
[ 6488.476665] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6488.476672] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6488.476676] usb 1-1.2: Product: YP-U6
[ 6488.476679] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6488.476683] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6488.481056] usb 1-1.2: can't set config #1, error -71
[ 6488.481419] usb 1-1.2: USB disconnect, device number 112
[ 6488.702793] usb 1-1.2: new high-speed USB device number 113 using ehci-pci
[ 6488.823299] usb 1-1.2: device descriptor read/all, error -71
[ 6489.118727] usb 1-1.2: new high-speed USB device number 114 using ehci-pci
[ 6489.228668] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6489.228674] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6489.228677] usb 1-1.2: Product: YP-U6
[ 6489.228680] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6489.228683] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6489.229672] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6489.231245] scsi host5: usb-storage 1-1.2:1.0
[ 6489.523763] usb 1-1.2: USB disconnect, device number 114
[ 6489.746691] usb 1-1.2: new high-speed USB device number 115 using ehci-pci
[ 6489.856547] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6489.856554] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6489.856557] usb 1-1.2: Product: YP-U6
[ 6489.856561] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6489.856564] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6489.857218] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6489.857575] scsi host5: usb-storage 1-1.2:1.0
[ 6490.880584] scsi 5:0:0:0: Direct-Access     Samsung  YP-U6            0100 PQ: 0 ANSI: 4
[ 6490.881211] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 6490.882306] sd 5:0:0:0: [sdb] 912320 2048-byte logical blocks: (1.87 GB/1.74 GiB)
[ 6490.882934] sd 5:0:0:0: [sdb] Write Protect is off
[ 6490.882939] sd 5:0:0:0: [sdb] Mode Sense: 3e 00 00 00
[ 6490.883550] sd 5:0:0:0: [sdb] No Caching mode page found
[ 6490.883558] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 6490.890693]  sdb: sdb1
[ 6490.893922] sd 5:0:0:0: [sdb] Attached SCSI removable disk
[ 6491.610536] usb 1-1.2: reset high-speed USB device number 115 using ehci-pci
[ 6492.646893] usb 1-1-port2: Cannot enable. Maybe the USB cable is bad?
[ 6492.726440] usb 1-1.2: reset high-speed USB device number 115 using ehci-pci
[ 6494.222295] usb 1-1.2: reset high-speed USB device number 115 using ehci-pci
[ 6494.638246] usb 1-1.2: device not accepting address 115, error -22
[ 6494.926223] usb 1-1.2: reset high-speed USB device number 115 using ehci-pci
[ 6495.342201] usb 1-1.2: device not accepting address 115, error -22
[ 6495.342787] usb 1-1.2: USB disconnect, device number 115
[ 6495.358206] sd 5:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 6495.358211] sd 5:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 00 0d eb b0 00 00 02 00
[ 6495.358213] print_req_error: I/O error, dev sdb, sector 3649216
[ 6495.614165] usb 1-1.2: new high-speed USB device number 116 using ehci-pci
[ 6496.686224] usb 1-1-port2: Cannot enable. Maybe the USB cable is bad?
[ 6496.766071] usb 1-1.2: new high-speed USB device number 117 using ehci-pci
[ 6497.481929] usb 1-1.2: device descriptor read/64, error -71
[ 6497.889974] usb 1-1.2: device descriptor read/64, error -71
[ 6497.998161] usb 1-1-port2: attempt power cycle
[ 6498.601912] usb 1-1.2: new high-speed USB device number 118 using ehci-pci
[ 6498.631065] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6498.631067] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6498.631068] usb 1-1.2: Product: YP-U6
[ 6498.631070] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6498.631071] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6498.648154] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6498.648367] scsi host5: usb-storage 1-1.2:1.0
[ 6498.648811] usb 1-1.2: USB disconnect, device number 118
[ 6498.897867] usb 1-1.2: new high-speed USB device number 119 using ehci-pci
[ 6499.613826] usb 1-1.2: device descriptor read/64, error -71
[ 6500.586011] usb 1-1-port2: Cannot enable. Maybe the USB cable is bad?
[ 6500.665701] usb 1-1.2: new high-speed USB device number 120 using ehci-pci
[ 6501.193698] usb 1-1.2: device descriptor read/64, error -71
[ 6501.809591] usb 1-1.2: device descriptor read/64, error -71
[ 6501.917797] usb 1-1-port2: attempt power cycle
[ 6503.145506] usb 1-1.2: new high-speed USB device number 121 using ehci-pci
[ 6503.569393] usb 1-1.2: device not accepting address 121, error -71
[ 6504.065412] usb 1-1.2: new high-speed USB device number 122 using ehci-pci
[ 6504.095474] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6504.095479] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6504.095483] usb 1-1.2: Product: YP-U6
[ 6504.095486] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6504.095489] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6504.096441] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6504.096746] scsi host5: usb-storage 1-1.2:1.0
[ 6504.115465] usb 1-1.2: USB disconnect, device number 122
[ 6504.361401] usb 1-1.2: new high-speed USB device number 123 using ehci-pci
[ 6504.471355] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6504.471361] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6504.471366] usb 1-1.2: Product: YP-U6
[ 6504.471370] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6504.471373] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6504.472150] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6504.472477] scsi host5: usb-storage 1-1.2:1.0
[ 6504.627645] usb 1-1.2: USB disconnect, device number 123
[ 6504.869374] usb 1-1.2: new high-speed USB device number 124 using ehci-pci
[ 6505.733528] usb 1-1-port2: Cannot enable. Maybe the USB cable is bad?
[ 6506.021262] usb 1-1.2: new high-speed USB device number 125 using ehci-pci
[ 6506.737165] usb 1-1.2: device descriptor read/64, error -71
[ 6507.349124] usb 1-1.2: device not accepting address 125, error -71
[ 6507.349292] usb 1-1-port2: attempt power cycle
[ 6508.369032] usb 1-1.2: new high-speed USB device number 126 using ehci-pci
[ 6508.399116] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6508.399121] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6508.399124] usb 1-1.2: Product: YP-U6
[ 6508.399127] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6508.399130] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6508.400081] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6508.401620] scsi host5: usb-storage 1-1.2:1.0
[ 6508.402364] usb 1-1.2: USB disconnect, device number 126
[ 6508.649020] usb 1-1.2: new high-speed USB device number 127 using ehci-pci
[ 6509.152966] usb 1-1.2: device not accepting address 127, error -71
[ 6509.648915] usb 1-1.2: new high-speed USB device number 4 using ehci-pci
[ 6510.382741] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[ 6510.382745] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 6510.382747] usb 1-1.2: Product: YP-U6
[ 6510.382749] usb 1-1.2: Manufacturer: Samsung Electronics
[ 6510.382751] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[ 6510.383423] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6510.384924] scsi host5: usb-storage 1-1.2:1.0

total 12
drwxr-xr-x   3 root root 4096 janv. 21 17:28 .
drwxr-xr-x  24 root root 4096 janv. 21 18:57 ..
drwxr-x---+  2 root root 4096 janv. 22 11:52 cl

total 8
drwxr-x---+ 2 root root 4096 janv. 22 11:52 .
drwxr-xr-x  3 root root 4096 janv. 21 17:28 ..

ii nautilus 1:3.26.4-0~ubuntu18.04.3 amd64
ii nemo 3.6.5-1 amd64
ii nemo-data 3.6.5-1 all

lrwxrwxrwx 1 root root  9 janv. 22 10:09 ata-HL-DT-ST_DVDRAM_GTB0N_KZ7F23F3153 -> ../../sr0
lrwxrwxrwx 1 root root 10 janv. 22 10:09 wwn-0x50026b776402dc5c-part1 -> ../../sda1
lrwxrwxrwx 1 root root 10 janv. 22 10:09 ata-KINGSTON_SHFS37A240G_50026B776402DC5C-part1 -> ../../sda1

Description:	Ubuntu 18.04.1 LTS

4.15.0-43-generic x86_64

[sub]Modération : merci d'utiliser les balises code (explications ici).[/sub]

LeJediGris

Salut,

C'est sur le même PC ?, change de port USB pour voir, c'est une clé usb 3 ? (puisque ehci et pas xhci).
Arrête ton PC et débranche-le (si portable enlève la batterie) pendant 5-10 minutes puis réessaye (cas ou les alims USB seraient fautives)

A+

moko138

Montre

dpkg -l | grep -Ev "pptp|smtp" | grep -Ei "gphoto|mtp|ptp"

moko138

Salut, LeJediGris !
Je n'arrive pas à trouver une définition de l' "error -71".
Sais-tu en quoi elle consiste ?

- -

La clef 04e8:5133, bizarrement, n'apparaît pas dans lsusb, bien que visible dans dmesg.

Elle n'est pas répertoriée sur https://usb-ids.gowdy.us/read/UD/04e8
Mais on voit des "cousines" utilisant le protocole mtp/ptp.

xubu1957

Bonjour,

@moko138

Avec la réponse > superuser.com/questions/875922/how-to-understand-and-debug-usb-issues-with-linux ?

Samsara035

Réponse de la commande:

Moko138 a écritdpkg -l | grep -Ev "pptp|smtp" | grep -Ei "gphoto|mtp|ptp"

cl@cl-CX61-2QF:~$ dpkg -l | grep -Ev "pptp|smtp" | grep -Ei "gphoto|mtp|ptp"
ii  libgphoto2-6:amd64                         2.5.16-2                                     amd64        gphoto2 digital camera library
ii  libgphoto2-l10n                            2.5.16-2                                     all          gphoto2 digital camera library - localized messages
ii  libgphoto2-port12:amd64                    2.5.16-2                                     amd64        gphoto2 digital camera port library
ii  libmtp-common                              1.1.13-1                                     all          Media Transfer Protocol (MTP) common files
ii  libmtp-runtime                             1.1.13-1                                     amd64        Media Transfer Protocol (MTP) runtime tools
ii  libmtp9:amd64                              1.1.13-1                                     amd64        Media Transfer Protocol (MTP) library

xubu1957

~~Pour ajouter toi-même les balises code à ton précédent message #8~~ : Merci 😉

Cliquer sur le lien « Modifier » en bas à droite du message
Sélectionner le texte
Cliquer sur le <> de l'éditeur de message

comme indiqué dans le : Retour utilisable de commande

moko138

Sur ma Debian, j'ai en plus le paquet gphoto2.
Ne l'avez-vous pas, vous qui avez une Ubuntu en service ?

moko138

xubu1957 a écrit @moko138

Avec la réponse > superuser.com/questions/875922/how-to-understand-and-debug-usb-issues-with-linux ?

Merci mais... tu y vois l'esquisse de l'ombre d'une définition de l' "error -71" ?

Samsara035

LeJediGris a écritSalut,

C'est sur le même PC ?, change de port USB pour voir, c'est une clé usb 3 ? (puisque ehci et pas xhci).
Arrête ton PC et débranche-le (si portable enlève la batterie) pendant 5-10 minutes puis réessaye (cas ou les alims USB seraient fautives)

A+

Oui, sur le même pc.J'ai testé mes 3 port usb.J'ai débranché la batterie...
Toujours le même problème.
Par contre, j'ai un netbook (xubuntu) qui la reconnaît sans problème.
Je crois que je vais laisser tomber.
Merci pour votre aide

xubu1957

Bonjour,

@moko138

J'avais lu :

traduction a écritLes codes d’état USB et leurs raisons possibles se trouvent dans la source de votre noyau, sous forme de fichier Documentation/usb/error-codes.txt. Dans Debian Stretch, cela est contenu dans le paquet linux-doc, qui l’installe dans /usr/share/doc/linux-doc-4.9/Documentation/usb/error-codes.txt.gz.

Notez que les erreurs dans ce fichier sont données par leur nom (comme -71être EPROTO); pour trouver le numéro / nom correspondant, vous devez:

grep -w 71 /usr/include/asm-generic/errno*.h
ou pour une autre manière:

grep -w EPROTO /usr/include/asm-generic/errno*.h
assurez-vous que les fichiers d'inclusion de développement sont présents sur le système (dans Debian, en faisant apt-get install linux-libc-dev, sinon vous n'obtiendrez aucune correspondance ...

mais n'étant pas spécialiste !

moko138

Merci !
Après installation de linux-doc et décompression du .gz :

cat error-codes.txt
Revised: 2004-Oct-21

This is the documentation of (hopefully) all possible error codes (and
their interpretation) that can be returned from usbcore.

Some of them are returned by the Host Controller Drivers (HCDs), which
device drivers only see through usbcore.  As a rule, all the HCDs should
behave the same except for transfer speed dependent behaviors and the
way certain faults are reported.


**************************************************************************
*                   Error codes returned by usb_submit_urb               *
**************************************************************************

Non-USB-specific:

0		URB submission went fine

-ENOMEM		no memory for allocation of internal structures	

USB-specific:

-ENODEV		specified USB-device or bus doesn't exist

-ENOENT		specified interface or endpoint does not exist or
		is not enabled

-ENXIO		host controller driver does not support queuing of this type
		of urb.  (treat as a host controller bug.)

-EINVAL		a) Invalid transfer type specified (or not supported)
		b) Invalid or unsupported periodic transfer interval
		c) ISO: attempted to change transfer interval
		d) ISO: number_of_packets is < 0
		e) various other cases

-EAGAIN		a) specified ISO start frame too early
		b) (using ISO-ASAP) too much scheduled for the future
		   wait some time and try again.

-EFBIG		Host controller driver can't schedule that many ISO frames.

-EPIPE		The pipe type specified in the URB doesn't match the
		endpoint's actual type.

-EMSGSIZE	(a) endpoint maxpacket size is zero; it is not usable
		    in the current interface altsetting.
		(b) ISO packet is larger than the endpoint maxpacket.
		(c) requested data transfer length is invalid: negative
		    or too large for the host controller.

-ENOSPC		This request would overcommit the usb bandwidth reserved
		for periodic transfers (interrupt, isochronous).

-ESHUTDOWN	The device or host controller has been disabled due to some
		problem that could not be worked around.

-EPERM		Submission failed because urb->reject was set.

-EHOSTUNREACH	URB was rejected because the device is suspended.

-ENOEXEC	A control URB doesn't contain a Setup packet.


**************************************************************************
*                   Error codes returned by in urb->status               *
*                   or in iso_frame_desc[n].status (for ISO)             *
**************************************************************************

USB device drivers may only test urb status values in completion handlers.
This is because otherwise there would be a race between HCDs updating
these values on one CPU, and device drivers testing them on another CPU.

A transfer's actual_length may be positive even when an error has been
reported.  That's because transfers often involve several packets, so that
one or more packets could finish before an error stops further endpoint I/O.

For isochronous URBs, the urb status value is non-zero only if the URB is
unlinked, the device is removed, the host controller is disabled, or the total
transferred length is less than the requested length and the URB_SHORT_NOT_OK
flag is set.  Completion handlers for isochronous URBs should only see
urb->status set to zero, -ENOENT, -ECONNRESET, -ESHUTDOWN, or -EREMOTEIO.
Individual frame descriptor status fields may report more status codes.


0			Transfer completed successfully

-ENOENT			URB was synchronously unlinked by usb_unlink_urb

-EINPROGRESS		URB still pending, no results yet
			(That is, if drivers see this it's a bug.)

-EPROTO (*, **)		a) bitstuff error
			b) no response packet received within the
			   prescribed bus turn-around time
			c) unknown USB error 

-EILSEQ (*, **)		a) CRC mismatch
			b) no response packet received within the
			   prescribed bus turn-around time
			c) unknown USB error 

			Note that often the controller hardware does not
			distinguish among cases a), b), and c), so a
			driver cannot tell whether there was a protocol
			error, a failure to respond (often caused by
			device disconnect), or some other fault.

-ETIME (**)		No response packet received within the prescribed
			bus turn-around time.  This error may instead be
			reported as -EPROTO or -EILSEQ.

-ETIMEDOUT		Synchronous USB message functions use this code
			to indicate timeout expired before the transfer
			completed, and no other error was reported by HC.

-EPIPE (**)		Endpoint stalled.  For non-control endpoints,
			reset this status with usb_clear_halt().

-ECOMM			During an IN transfer, the host controller
			received data from an endpoint faster than it
			could be written to system memory

-ENOSR			During an OUT transfer, the host controller
			could not retrieve data from system memory fast
			enough to keep up with the USB data rate

-EOVERFLOW (*)		The amount of data returned by the endpoint was
			greater than either the max packet size of the
			endpoint or the remaining buffer size.  "Babble".

-EREMOTEIO		The data read from the endpoint did not fill the
			specified buffer, and URB_SHORT_NOT_OK was set in
			urb->transfer_flags.

-ENODEV			Device was removed.  Often preceded by a burst of
			other errors, since the hub driver doesn't detect
			device removal events immediately.

-EXDEV			ISO transfer only partially completed
			(only set in iso_frame_desc[n].status, not urb->status)

-EINVAL			ISO madness, if this happens: Log off and go home

-ECONNRESET		URB was asynchronously unlinked by usb_unlink_urb

-ESHUTDOWN		The device or host controller has been disabled due
			to some problem that could not be worked around,
			such as a physical disconnect.


(*) Error codes like -EPROTO, -EILSEQ and -EOVERFLOW normally indicate
hardware problems such as bad devices (including firmware) or cables.

(**) This is also one of several codes that different kinds of host
controller use to indicate a transfer has failed because of device
disconnect.  In the interval before the hub driver starts disconnect
processing, devices may receive such fault reports for every request.



**************************************************************************
*              Error codes returned by usbcore-functions                 *
*           (expect also other submit and transfer status codes)         *
**************************************************************************

usb_register():
-EINVAL			error during registering new driver

usb_get_*/usb_set_*():
usb_control_msg():
usb_bulk_msg():
-ETIMEDOUT		Timeout expired before the transfer completed.

Déception :
pas trace de code numérique d'erreur !
Pas trace non plus de point commun entre les erreurs décrites par ce fichier et celles contenues dans dmesg.

À défaut, les explications

a) (...) ou b) (...) ou c) (...) ou d) (...) ou e) autres cas variés

a) (...) ou b) (...) ou c) erreur USB inconnue

j'ai adoré !

- -
Mais il est vrai que

grep -w 71 /usr/include/asm-generic/errno*.h

(pourquoi "asm-generic" ???)
répond :

/usr/include/asm-generic/errno.h:#define	EPROTO		71	/* Protocol error */

et que "EPROTO est expliqué :

-ETIME (**)		No response packet received within the prescribed
			bus turn-around time.  This error may instead be
			reported as -EPROTO

-EPROTO (*, **)		a) bitstuff error
			b) no response packet received within the
			   prescribed bus turn-around time
			c) unknown USB error

Quant à trouver une traduction de "bitstuff"...
dans l'cu(sb), la balayette-stuff !

[center]= =[/center]

Samsara035, en #3, tu as écrit :

[ 6460.717335] usb 1-1.2: USB disconnect, device number 88

Merci de recommencer,
en débranchant la clef bluetooth
puis (comme indiqué dans la procédure)
en démarrant le système.

LeJediGris

Salut

@moko (sans rancune... 😛 )
Bitstuffing ou bourrage de bits, et non ce n'est pas cochon ou du prOn.

A+

moko138

Merci LeJediGris !

Samsara035

moko138 a écritSur ma Debian, j'ai en plus le paquet gphoto2.
Ne l'avez-vous pas, vous qui avez une Ubuntu en service ?

Je viens de l'installer mais ça ne change rien...

Samsara035

moko138: merci de ton aide
Retour de la commande:

cl@cl-CX61-2QF:~$ dmesg | tail -1 > ~/tail.txt ; sleep 45 && echo ; mount -l | tail -1 ; echo ; lsusb | sort ; echo ; lsusb -t ; echo ; dmesg | grep -A1000 "$(sed -r 's/([].[])/\\\1/g' ~/tail.txt)" | grep -Evi "80211|associate|authenticat|dhclient|dhcp|forcedeth|ipv6|link is not ready|network|no link during initialization|phy[0-9]|tx/rx|tx status|ufw|wlan"; echo; ls -la /media ; echo; ls -la /media/$USER ; echo; dpkg -l | grep -i "file manager" | grep -v plugin | tr -s " " | cut -d" " -s -f1,2,3,4 ; echo; ls -lrt /dev/disk/by-id | tail -3 ; echo ; lsb_release -d ; echo ; uname -mr ; echo ; whoami

/dev/sdc1 on /media/cl/F009-64A5 type vfat (rw,nosuid,nodev,relatime,uid=1000,gid=1000,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,showexec,utf8,flush,errors=remount-ro,uhelper=udisks2)

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:8008 Intel Corp. 
Bus 001 Device 003: ID 13d3:3394 IMC Networks Bluetooth
Bus 001 Device 006: ID 04e8:5133 Samsung Electronics Co., Ltd 
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 002: ID 8087:8000 Intel Corp. 
Bus 002 Device 003: ID 0bda:0138 Realtek Semiconductor Corp. RTS5138 Card Reader Controller
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 002: ID 05ac:12a0 Apple, Inc. iPhone 4S
Bus 003 Device 003: ID 09da:022b A4Tech Co., Ltd. Wireless Mouse (Battery Free)
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub

/:  Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/4p, 5000M
/:  Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/14p, 480M
    |__ Port 1: Dev 2, If 1, Class=Vendor Specific Class, Driver=usbfs, 480M
    |__ Port 1: Dev 2, If 2, Class=Vendor Specific Class, Driver=ipheth, 480M
    |__ Port 1: Dev 2, If 0, Class=Imaging, Driver=usbfs, 480M
    |__ Port 2: Dev 3, If 0, Class=Human Interface Device, Driver=usbhid, 1.5M
/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/2p, 480M
    |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/8p, 480M
        |__ Port 3: Dev 3, If 0, Class=Mass Storage, Driver=ums-realtek, 480M
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/2p, 480M
    |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/6p, 480M
        |__ Port 2: Dev 6, If 0, Class=Mass Storage, Driver=usb-storage, 480M
        |__ Port 3: Dev 3, If 0, Class=Wireless, Driver=btusb, 12M
        |__ Port 3: Dev 3, If 1, Class=Wireless, Driver=btusb, 12M

[   18.703523] FAT-fs (sdc1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[   75.132009] usb 1-1.2: new high-speed USB device number 4 using ehci-pci
[   75.242031] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[   75.242038] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[   75.242042] usb 1-1.2: Product: YP-U6
[   75.242046] usb 1-1.2: Manufacturer: Samsung Electronics
[   75.242050] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[   75.242847] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[   75.243220] scsi host6: usb-storage 1-1.2:1.0
[   75.423019] usb 1-1.2: USB disconnect, device number 4
[   75.644091] usb 1-1.2: new high-speed USB device number 5 using ehci-pci
[   75.754027] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[   75.754033] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[   75.754037] usb 1-1.2: Product: YP-U6
[   75.754040] usb 1-1.2: Manufacturer: Samsung Electronics
[   75.754043] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[   75.754702] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[   75.754998] scsi host6: usb-storage 1-1.2:1.0
[   75.935373] usb 1-1.2: USB disconnect, device number 5
[   76.172087] usb 1-1.2: new high-speed USB device number 6 using ehci-pci
[   76.282033] usb 1-1.2: New USB device found, idVendor=04e8, idProduct=5133
[   76.282040] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[   76.282044] usb 1-1.2: Product: YP-U6
[   76.282048] usb 1-1.2: Manufacturer: Samsung Electronics
[   76.282052] usb 1-1.2: SerialNumber: 293300006D6C8D3B0002DCDF7FD08D3B
[   76.282830] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[   76.283062] scsi host6: usb-storage 1-1.2:1.0
[   77.308684] scsi 6:0:0:0: Direct-Access     Samsung  YP-U6            0100 PQ: 0 ANSI: 4
[   77.309055] sd 6:0:0:0: Attached scsi generic sg3 type 0
[   77.309779] sd 6:0:0:0: [sdd] 912320 2048-byte logical blocks: (1.87 GB/1.74 GiB)
[   77.310397] sd 6:0:0:0: [sdd] Write Protect is off
[   77.310400] sd 6:0:0:0: [sdd] Mode Sense: 3e 00 00 00
[   77.311024] sd 6:0:0:0: [sdd] No Caching mode page found
[   77.311030] sd 6:0:0:0: [sdd] Assuming drive cache: write through
[   77.316669]  sdd: sdd1
[   77.320539] sd 6:0:0:0: [sdd] Attached SCSI removable disk
[   77.731983] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   78.383978] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   78.683976] usb 1-1.2: device descriptor read/64, error -71
[   79.111970] usb 1-1.2: device descriptor read/64, error -71
[   79.507991] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   80.011984] usb 1-1.2: device not accepting address 6, error -71
[   80.512019] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   80.556535] usb 1-1.2: device descriptor read/8, error -71
[   80.696533] usb 1-1.2: device descriptor read/8, error -71
[   81.092025] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   81.551976] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   82.207987] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   82.707978] usb 1-1.2: device not accepting address 6, error -71
[   83.207966] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   83.556404] usb 1-1.2: device descriptor read/all, error -71
[   83.855989] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   84.207980] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   84.631990] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   84.740671] sd 6:0:0:0: [sdd] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[   84.740676] sd 6:0:0:0: [sdd] tag#0 CDB: Read(10) 28 00 00 0d eb 40 00 00 1c 00
[   84.740679] print_req_error: I/O error, dev sdd, sector 3648768
[   85.071973] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   85.420409] usb 1-1.2: device descriptor read/all, error -71
[   85.715982] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   86.359987] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   86.995975] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   87.419986] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   87.719978] usb 1-1.2: device descriptor read/64, error -71
[   88.267982] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   88.568037] usb 1-1.2: device descriptor read/64, error -71
[   89.300075] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   89.720075] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   90.355988] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   90.655994] usb 1-1.2: device descriptor read/64, error -71
[   91.480025] usb 1-1.2: device descriptor read/64, error -71
[   91.876036] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   92.680065] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   93.236104] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   94.196077] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   94.776083] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   94.885330] sd 6:0:0:0: [sdd] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[   94.885339] sd 6:0:0:0: [sdd] tag#0 CDB: Read(10) 28 00 00 0d eb 5e 00 00 20 00
[   94.885343] print_req_error: I/O error, dev sdd, sector 3648888
[   95.236016] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   96.156075] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   96.728002] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   97.212080] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   98.304073] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   98.720078] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   99.560071] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[   99.680556] usb 1-1.2: device descriptor read/all, error -71
[   99.976078] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  100.528065] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  100.980057] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  102.172079] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  102.612026] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  103.316059] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  103.425289] sd 6:0:0:0: [sdd] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  103.425294] sd 6:0:0:0: [sdd] tag#0 CDB: Read(10) 28 00 00 0d eb 40 00 00 02 00
[  103.425296] print_req_error: I/O error, dev sdd, sector 3648768
[  103.425302] Buffer I/O error on dev sdd, logical block 456096, async page read
[  103.756082] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  104.204086] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  104.624081] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  105.256024] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  105.856083] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  106.272078] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  106.964078] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  107.692070] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  108.184047] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  108.484041] usb 1-1.2: device descriptor read/64, error -71
[  108.892076] usb 1-1.2: device descriptor read/64, error -71
[  109.080075] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  109.736079] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  110.556037] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  111.124052] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  111.233314] sd 6:0:0:0: [sdd] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  111.233320] sd 6:0:0:0: [sdd] tag#0 CDB: Read(10) 28 00 00 00 04 00 00 00 02 00
[  111.233323] print_req_error: I/O error, dev sdd, sector 4096
[  112.568050] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  113.152071] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  113.452074] usb 1-1.2: device descriptor read/64, error -71
[  114.192052] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  115.384079] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  116.104077] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  116.664026] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  117.208080] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci
[  118.084091] usb 1-1.2: reset high-speed USB device number 6 using ehci-pci

total 12
drwxr-xr-x   3 root root 4096 janv. 21 17:28 .
drwxr-xr-x  24 root root 4096 janv. 21 18:57 ..
drwxr-x---+  3 root root 4096 janv. 23 19:57 cl

total 40
drwxr-x---+  3 root root  4096 janv. 23 19:57 .
drwxr-xr-x   3 root root  4096 janv. 21 17:28 ..
drwxr-xr-x  19 cl   cl   32768 janv.  1  1970 F009-64A5

ii nautilus 1:3.26.4-0~ubuntu18.04.3 amd64
rc nemo 3.6.5-1 amd64

lrwxrwxrwx 1 root root 10 janv. 23 19:57 ata-TOSHIBA_MQ01ABF050_15CEWKXQT-part2 -> ../../sda2
lrwxrwxrwx 1 root root 10 janv. 23 19:57 wwn-0x5000039604b01e86-part1 -> ../../sda1
lrwxrwxrwx 1 root root 10 janv. 23 19:57 ata-TOSHIBA_MQ01ABF050_15CEWKXQT-part1 -> ../../sda1

Description:	Ubuntu 18.04.1 LTS

4.15.0-43-generic x86_64

xubu1957

Bonjour,

@moko138

Cette liste (2009) > virtsync.com/c-error-codes-include-errno pour info.

ou plus récent > gist.github.com/nullunar

moko138

On avance ! 🙂

Ce qui m'a frappé, c'est l'apparente contradiction entre
dmesg qui voit la clef mp3 YP-U6 04e8:5133
et lsusb qui, en #3, au même moment, ne la voyait pas.

/![/b] Mais en #18, lsusb la voit :

Bus 001 Device 006: ID 04e8:5133 Samsung Electronics Co., Ltd

/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/2p, 480M
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/6p, 480M
|__ Port 2: Dev 6, If 0, Class=Mass Storage, Driver=usb-storage, 480M

Et je remarque maintenant plusieurs choses :
a) Entre dmesg qui enregistre en #18
"new high-speed USB device number 4"
et (45 secondes plus tard) lsusb qui liste la même clef en tant que
"Device 006: ID 04e8:5133",
il y a déjà eu deux (= 6-4) déconnexions, et ce avant même aucune "error -71" EPROTO.

b) La clef et sa partition sont bien reconnues, 🙂
- en #3 :
[ 6460.717335] usb 1-1.2: USB disconnect, device number 88
[ 6490.890693] sdb: sdb1
- et en #18 :
[ 18.703523] FAT-fs (sdc1)
[ 77.309779] sd 6:0:0:0: [sdd] 912320 2048-byte logical blocks: (1.87 GB/1.74 GiB)
[ 77.316669] sdd: sdd1

c) Ce n'est qu'après ces reconnaissances qu'apparaissent les "error -71".
Et aussi des erreurs d'entrée/sortie :
[ 84.740671] sd 6:0:0:0: [sdd] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 84.740676] sd 6:0:0:0: [sdd] tag#0 CDB: Read(10) 28 00 00 0d eb 40 00 00 1c 00
[ 84.740679] print_req_error: I/O error, dev sdd, sector 3648768
[ 94.885343] print_req_error: I/O error, dev sdd, sector 3648888
[ 103.425296] print_req_error: I/O error, dev sdd, sector 3648768
[ 103.425302] Buffer I/O error on dev sdd, logical block 456096, async page read
[ 111.233323] print_req_error: I/O error, dev sdd, sector 4096

Error codes like -EPROTO, -EILSEQ and -EOVERFLOW normally indicate
hardware problems such as bad devices (including firmware) or cables.

Et en effet, en #3 (mais pas en #8 !) on a quatre doutes exprimés sur un cable en 45" :

[ 6492.646893] usb 1-1-port2: Cannot enable. Maybe the USB cable is bad?
[ 6492.726440] usb 1-1.2: reset high-speed USB device number 115 using ehci-pci
[ 6494.222295] usb 1-1.2: reset high-speed USB device number 115 using ehci-pci
[ 6494.638246] usb 1-1.2: device not accepting address 115, error -22
[ 6494.926223] usb 1-1.2: reset high-speed USB device number 115 using ehci-pci
[ 6495.342201] usb 1-1.2: device not accepting address 115, error -22
[ 6495.342787] usb 1-1.2: USB disconnect, device number 115

Tiens l' "error -22" : à chercher aussi :

grep -w 22 /usr/include/asm-generic/errno*.h
/usr/include/asm-generic/errno-base.h:#define	EINVAL		22	/* Invalid argument */

-EINVAL		a) Invalid transfer type specified (or not supported)
		b) Invalid or unsupported periodic transfer interval
		c) ISO: attempted to change transfer interval
		d) ISO: number_of_packets is < 0
		e) various other cases

xubu1957 :
Merci !

Samsara035 :
Merci de préciser ce qui est monté en /media/<toi>/F009-64A5. et qui a besoin d'être vérifié par un windows quelconque.
Entre #3 et #18, tu as branché des périphériques usb supplémentaires.
Mais l'idée, c'est de ne brancher que le strict minimum de périphériques,
- pour éviter des conflits entre périphériques ;
- pour éviter des problèmes d'alimentation (pas toujours suffisante).

Concrètement,
Dis-nous si tu as des données à récupérer sur cette clef de 1.87 Go.
Dis-nous s'il y a un câble entre ta clef mp3 et la carte-mère.
S'il y a un câble, remplace-le et dis-nous si ça change quelque-chose.
S'il n'y a pas de câble, change de prise usb, n'intercale pas de hub, surtout pas ! Et dis-nous si ça change quelque-chose.
Clef branchée depuis au moins une minute (prenons de la marge) montre :

sudo lsblk -o name,fstype,label,size,mountpoint | grep -v "loop"; echo; ls -lt /dev/disk/by-id | grep -v "\-part"

Page suivante »