Voici le résultat de la première commande : on est toujours à 45916 erreurs
a2mains@PC-markorki:/home/marc$
a2mains@PC-markorki:/home/marc$ sudo smartctl -a /dev/disk/by-id/ata-WDC_WD20EFRX-68EUZN0_WD-WCC4M0974286
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-54-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD20EFRX-68EUZN0
Serial Number: WD-WCC4M0974286
LU WWN Device Id: 5 0014ee 2b42f8804
Firmware Version: 80.00A80
User Capacity: 2000398934016 bytes [2,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sun Jul 28 13:06:06 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (28200) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 285) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 193 165 021 Pre-fail Always - 3333
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1974
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 075 075 000 Old_age Always - 18372
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1974
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 298
193 Load_Cycle_Count 0x0032 141 141 000 Old_age Always - 179172
194 Temperature_Celsius 0x0022 105 095 000 Old_age Always - 42
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 45916 inconsistent with error log pointer 2
ATA Error Count: 45916 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 45916 occurred at disk power-on lifetime: 18324 hours (763 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 08 00:13:33.227 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:13:33.226 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:13:33.226 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 00:13:33.226 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:13:33.225 IDENTIFY DEVICE
Error 45915 occurred at disk power-on lifetime: 18324 hours (763 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 08 00:13:33.226 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 00:13:33.226 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:13:33.225 IDENTIFY DEVICE
c8 00 08 00 10 59 ec 08 00:13:33.203 READ DMA
ef 10 02 00 00 00 a0 08 00:13:33.203 SET FEATURES [Enable SATA feature]
Error 45914 occurred at disk power-on lifetime: 18324 hours (763 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 08 00:13:33.226 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:13:33.225 IDENTIFY DEVICE
c8 00 08 00 10 59 ec 08 00:13:33.203 READ DMA
ef 10 02 00 00 00 a0 08 00:13:33.203 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:13:33.202 IDENTIFY DEVICE
Error 45913 occurred at disk power-on lifetime: 18324 hours (763 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 08 00 10 59 ec Device Fault; Error: ABRT 8 sectors at LBA = 0x0c591000 = 207163392
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 10 59 ec 08 00:13:33.203 READ DMA
ef 10 02 00 00 00 a0 08 00:13:33.203 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:13:33.202 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:13:33.202 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 00:13:33.202 SET FEATURES [Enable SATA feature]
Error 45912 occurred at disk power-on lifetime: 18324 hours (763 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 08 00:13:33.203 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:13:33.202 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:13:33.202 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 00:13:33.202 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:13:33.201 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Selective offline Completed without error 00% 18366 -
# 2 Extended offline Interrupted (host reset) 60% 18348 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
a2mains@PC-markorki:/home/marc$
Pour le "bon" disque :
a2mains@PC-markorki:/home/marc$
a2mains@PC-markorki:/home/marc$ sudo smartctl -l error /dev/disk/by-id/ata-WDC_WD20EFRX-68EUZN0_WD-WCC4M0970110
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-54-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF READ SMART DATA SECTION ===
SMART Error Log Version: 1
ATA Error Count: 41 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 41 occurred at disk power-on lifetime: 14990 hours (624 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 08 58 08 40 e0 Error: IDNF at LBA = 0x00400858 = 4196440
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 08 58 08 40 e0 00 03:21:17.337 WRITE DMA
Error 40 occurred at disk power-on lifetime: 14990 hours (624 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 48 c6 cc e0 Error: UNC 8 sectors at LBA = 0x00ccc648 = 13420104
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 48 c6 cc e0 00 03:20:34.611 READ DMA
Error 39 occurred at disk power-on lifetime: 14990 hours (624 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 10 98 21 80 e0 Error: IDNF at LBA = 0x00802198 = 8397208
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 10 98 21 80 e0 00 02:59:00.438 WRITE DMA
ec 00 00 00 00 00 a0 00 02:59:00.435 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 02:59:00.435 SET FEATURES [Set transfer mode]
Error 38 occurred at disk power-on lifetime: 14990 hours (624 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 10 98 21 80 e0 Error: IDNF at LBA = 0x00802198 = 8397208
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 10 98 21 80 e0 00 02:58:53.420 WRITE DMA
ec 00 00 00 00 00 a0 00 02:58:53.417 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 02:58:53.417 SET FEATURES [Set transfer mode]
Error 37 occurred at disk power-on lifetime: 14990 hours (624 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 10 98 21 80 e0 Error: IDNF at LBA = 0x00802198 = 8397208
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 10 98 21 80 e0 00 02:58:46.391 WRITE DMA
ec 00 00 00 00 00 a0 00 02:58:46.388 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 02:58:46.388 SET FEATURES [Set transfer mode]
a2mains@PC-markorki:/home/marc$
et le -a :
a2mains@PC-markorki:/home/marc$
a2mains@PC-markorki:/home/marc$ sudo smartctl -a /dev/disk/by-id/ata-WDC_WD20EFRX-68EUZN0_WD-WCC4M0970110
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-54-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD20EFRX-68EUZN0
Serial Number: WD-WCC4M0970110
LU WWN Device Id: 5 0014ee 209847e62
Firmware Version: 80.00A80
User Capacity: 2000398934016 bytes [2,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sun Jul 28 13:18:41 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (26640) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 269) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 47
3 Spin_Up_Time 0x0027 196 168 021 Pre-fail Always - 3200
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1670
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 1
9 Power_On_Hours 0x0032 080 080 000 Old_age Always - 15003
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1609
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 215
193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always - 839507
194 Temperature_Celsius 0x0022 102 092 000 Old_age Always - 45
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 41 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 41 occurred at disk power-on lifetime: 14990 hours (624 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 08 58 08 40 e0 Error: IDNF at LBA = 0x00400858 = 4196440
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 08 58 08 40 e0 00 03:21:17.337 WRITE DMA
Error 40 occurred at disk power-on lifetime: 14990 hours (624 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 48 c6 cc e0 Error: UNC 8 sectors at LBA = 0x00ccc648 = 13420104
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 48 c6 cc e0 00 03:20:34.611 READ DMA
Error 39 occurred at disk power-on lifetime: 14990 hours (624 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 10 98 21 80 e0 Error: IDNF at LBA = 0x00802198 = 8397208
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 10 98 21 80 e0 00 02:59:00.438 WRITE DMA
ec 00 00 00 00 00 a0 00 02:59:00.435 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 02:59:00.435 SET FEATURES [Set transfer mode]
Error 38 occurred at disk power-on lifetime: 14990 hours (624 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 10 98 21 80 e0 Error: IDNF at LBA = 0x00802198 = 8397208
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 10 98 21 80 e0 00 02:58:53.420 WRITE DMA
ec 00 00 00 00 00 a0 00 02:58:53.417 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 02:58:53.417 SET FEATURES [Set transfer mode]
Error 37 occurred at disk power-on lifetime: 14990 hours (624 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 10 98 21 80 e0 Error: IDNF at LBA = 0x00802198 = 8397208
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 10 98 21 80 e0 00 02:58:46.391 WRITE DMA
ec 00 00 00 00 00 a0 00 02:58:46.388 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 02:58:46.388 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Interrupted (host reset) 90% 14977 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
a2mains@PC-markorki:/home/marc$
