Super merci de bien vouloir m'aider voici le résultat.
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.0.0-23-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke,
www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Blue Mobile
Device Model: WDC WD5000LPVX-22V0TT0
Serial Number: WD-WX81AA372418
LU WWN Device Id: 5 0014ee 20968019f
Firmware Version: 01.01A01
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Dec 30 17:30:42 2019 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (10140) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 116) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 407
3 Spin_Up_Time 0x0027 153 149 021 Pre-fail Always - 1325
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2979
5 Reallocated_Sector_Ct 0x0033 152 152 140 Pre-fail Always - 2037
7 Seek_Error_Rate 0x002e 200 186 000 Old_age Always - 0
9 Power_On_Hours 0x0032 055 055 000 Old_age Always - 33115
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 2827
191 G-Sense_Error_Rate 0x0032 024 024 000 Old_age Always - 76
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 197
193 Load_Cycle_Count 0x0032 181 181 000 Old_age Always - 58844
194 Temperature_Celsius 0x0022 108 081 000 Old_age Always - 35
196 Reallocated_Event_Count 0x0032 184 028 000 Old_age Always - 16
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 53
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 107 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 107 occurred at disk power-on lifetime: 33074 hours (1378 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 f8 c8 12 10 e8 Error: UNC 248 sectors at LBA = 0x081012c8 = 135271112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 f8 10 12 10 e8 00 00:55:20.769 READ DMA
c8 00 08 08 12 10 e8 00 00:55:20.769 READ DMA
c8 00 08 00 12 10 e8 00 00:55:20.769 READ DMA
c8 00 08 80 09 11 e8 00 00:55:20.769 READ DMA
Error 106 occurred at disk power-on lifetime: 33074 hours (1378 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 f8 d0 0a 10 e8 Error: UNC 248 sectors at LBA = 0x08100ad0 = 135269072
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 f8 10 0a 10 e8 00 00:55:16.316 READ DMA
c8 00 08 08 0a 10 e8 00 00:55:16.315 READ DMA
c8 00 08 00 0a 10 e8 00 00:55:16.279 READ DMA
c8 00 08 90 09 11 e8 00 00:55:16.278 READ DMA
c8 00 08 e0 1a 11 e8 00 00:55:16.278 READ DMA
Error 105 occurred at disk power-on lifetime: 33074 hours (1378 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 60 e0 3e e8 Error: UNC 8 sectors at LBA = 0x083ee060 = 138338400
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 60 e0 3e e8 00 00:54:28.374 READ DMA
ca 00 28 d8 32 11 ed 00 00:54:28.374 WRITE DMA
ca 00 20 a0 32 11 ed 00 00:54:28.374 WRITE DMA
ca 00 18 68 32 11 ed 00 00:54:28.374 WRITE DMA
ca 00 28 00 30 11 ed 00 00:54:28.373 WRITE DMA
Error 104 occurred at disk power-on lifetime: 33074 hours (1378 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 60 e0 3e e8 Error: UNC 8 sectors at LBA = 0x083ee060 = 138338400
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 60 e0 3e e8 00 00:54:24.186 READ DMA
c8 00 08 58 e0 3e e8 00 00:54:24.186 READ DMA
c8 00 08 50 e0 3e e8 00 00:54:24.186 READ DMA
c8 00 08 48 e0 3e e8 00 00:54:24.186 READ DMA
c8 00 08 40 e0 3e e8 00 00:54:24.186 READ DMA
Error 103 occurred at disk power-on lifetime: 33074 hours (1378 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 e0 60 e0 3e e8 Error: UNC 224 sectors at LBA = 0x083ee060 = 138338400
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 e0 20 e0 3e e8 00 00:54:19.719 READ DMA
c8 00 80 20 6a 38 e8 00 00:54:19.718 READ DMA
c8 00 20 00 6a 38 e8 00 00:54:19.701 READ DMA
c8 00 c0 20 1e 9e e9 00 00:54:19.700 READ DMA
c8 00 88 e0 1e 9e e9 00 00:54:19.698 READ DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 33075 4667416
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
