J'ai installé smartontools, mais ce qu'il me répond est du chinois pour moi ! Il signale bien des erreurs, mais qu'en conclure ???
Merci d'avance si tu as le temps de regarder ça :
alain@Lara:~$ sudo smartctl -s on -a /dev/sdd
[sudo] Mot de passe de alain :
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-91-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint MP5
Device Model: SAMSUNG HM500JJ
Serial Number: S2HCJ1DB602292
LU WWN Device Id: 5 0024e9 004f4dc32
Firmware Version: 2AK10001
User Capacity: 500107862016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Thu Apr 2 13:01:27 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 6360) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 106) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 565
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 089 086 025 Pre-fail Always - 3398
4 Start_Stop_Count 0x0032 097 097 000 Old_age Always - 3482
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 49396
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 096 096 000 Old_age Always - 4533
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1341
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 1364
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 064 051 000 Old_age Always - 34 (Min/Max 13/49)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 099 000 Old_age Always - 3
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 84
223 Load_Retry_Count 0x0032 096 096 000 Old_age Always - 4533
225 Load_Cycle_Count 0x0032 066 066 000 Old_age Always - 352714
SMART Error Log Version: 1
ATA Error Count: 228 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 228 occurred at disk power-on lifetime: 49351 hours (2056 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 a8 2b 0d e0 Error: UNC 8 sectors at LBA = 0x000d2ba8 = 863144
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 a8 2b 0d e0 00 00:00:22.580 READ DMA
27 00 00 00 00 00 e0 00 00:00:22.580 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:22.579 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 00:00:22.579 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:00:22.579 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 227 occurred at disk power-on lifetime: 49351 hours (2056 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 a8 2b 0d e0 Error: UNC 8 sectors at LBA = 0x000d2ba8 = 863144
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 a8 2b 0d e0 00 00:00:22.578 READ DMA
c8 00 08 b0 28 0d e0 00 00:00:22.578 READ DMA
c8 00 08 b8 25 0d e0 00 00:00:22.578 READ DMA
c8 00 08 b8 22 0d e0 00 00:00:22.578 READ DMA
c8 00 08 c0 1f 0d e0 00 00:00:22.578 READ DMA
Error 226 occurred at disk power-on lifetime: 49351 hours (2056 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 c8 bb 0c e0 Error: UNC 8 sectors at LBA = 0x000cbbc8 = 834504
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 c8 bb 0c e0 00 00:00:22.574 READ DMA
27 00 00 00 00 00 e0 00 00:00:22.574 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:22.574 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 00:00:22.574 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:00:22.574 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 225 occurred at disk power-on lifetime: 49351 hours (2056 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 c8 bb 0c e0 Error: UNC 8 sectors at LBA = 0x000cbbc8 = 834504
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 c8 bb 0c e0 00 00:00:22.572 READ DMA
c8 00 08 20 b9 0c e0 00 00:00:22.572 READ DMA
c8 00 08 78 b6 0c e0 00 00:00:22.572 READ DMA
c8 00 08 d0 b3 0c e0 00 00:00:22.572 READ DMA
c8 00 08 78 07 0d e0 00 00:00:22.572 READ DMA
Error 224 occurred at disk power-on lifetime: 49350 hours (2056 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 18 08 00 e0 Error: UNC 8 sectors at LBA = 0x00000818 = 2072
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 18 08 00 e0 00 00:00:17.455 READ DMA
ea 00 00 07 0a 00 e0 00 00:00:17.455 FLUSH CACHE EXT
ea 00 00 07 0a 00 e0 00 00:00:17.455 FLUSH CACHE EXT
c8 00 08 00 0a 00 e0 00 00:00:17.455 READ DMA
c8 00 08 10 08 00 e0 00 00:00:17.455 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
