Bonjour,
Vu le temps que je peux rester sur le pc à cause de ce problème, je vais le faire étape par étape
harlocksama@TEXTORM974MB:~$ sudo parted -l
[sudo] Mot de passe de harlocksama :
Modèle: ATA WDC WD5000HHTZ-0 (scsi)
Disque /dev/sda : 500GB
Taille des secteurs (logiques/physiques): 512B/4096B
Table de partitions : msdos
Disk Flags:
Numéro Début Fin Taille Type Système de fichiers Fanions
1 1049kB 4001MB 4000MB primary linux-swap(v1)
2 4001MB 54,0GB 50,0GB primary ext4 démarrage
3 54,0GB 104GB 50,0GB primary ext4
4 104GB 500GB 396GB primary ext4
Modèle: ATA WDC WD3202ABYS-0 (scsi)
Disque /dev/sdb : 320GB
Taille des secteurs (logiques/physiques): 512B/512B
Table de partitions : gpt
Disk Flags:
Numéro Début Fin Taille Système de fichiers Nom Fanions
1 17,4kB 320GB 320GB fat32 msftdata
Modèle: ATA WDC WD5002ABYS-0 (scsi)
Disque /dev/sdc : 500GB
Taille des secteurs (logiques/physiques): 512B/512B
Table de partitions : msdos
Disk Flags:
Numéro Début Fin Taille Type Système de fichiers Fanions
1 8225kB 500GB 500GB extended lba
5 8258kB 315GB 315GB logical ntfs
6 315GB 500GB 186GB logical ntfs
harlocksama@TEXTORM974MB:~$ smartctl
Le programme « smartctl » n'est pas encore installé. Vous pouvez l'installer en tapant :
sudo apt install smartmontools
harlocksama@TEXTORM974MB:~$ sudo apt install smartmontools
Lecture des listes de paquets... Fait
Construction de l'arbre des dépendances
Lecture des informations d'état... Fait
Les paquets supplémentaires suivants seront installés :
s-nail
Paquets suggérés :
exim4 | mail-transport-agent gsmartcontrol smart-notifier
Les NOUVEAUX paquets suivants seront installés :
s-nail smartmontools
0 mis à jour, 2 nouvellement installés, 0 à enlever et 8 non mis à jour.
Il est nécessaire de prendre 786 ko dans les archives.
Après cette opération, 2 202 ko d'espace disque supplémentaires seront utilisés.
Souhaitez-vous continuer ? [O/n] o
Réception de :1 http://fr.archive.ubuntu.com/ubuntu xenial/universe i386 s-nail i386 14.8.6-1 [350 kB]
Réception de :2 http://fr.archive.ubuntu.com/ubuntu xenial/main i386 smartmontools i386 6.4+svn4214-1 [436 kB]
786 ko réceptionnés en 0s (1 970 ko/s)
Sélection du paquet s-nail précédemment désélectionné.
(Lecture de la base de données... 542121 fichiers et répertoires déjà installés.)
Préparation du dépaquetage de .../s-nail_14.8.6-1_i386.deb ...
Dépaquetage de s-nail (14.8.6-1) ...
Sélection du paquet smartmontools précédemment désélectionné.
Préparation du dépaquetage de .../smartmontools_6.4+svn4214-1_i386.deb ...
Dépaquetage de smartmontools (6.4+svn4214-1) ...
Traitement des actions différées (« triggers ») pour menu (2.1.47ubuntu1.16.04.1) ...
Traitement des actions différées (« triggers ») pour man-db (2.7.5-1) ...
Traitement des actions différées (« triggers ») pour systemd (229-4ubuntu21.27) ...
Traitement des actions différées (« triggers ») pour ureadahead (0.100.0-19.1) ...
ureadahead will be reprofiled on next reboot
Paramétrage de s-nail (14.8.6-1) ...
update-alternatives: utilisation de « /usr/bin/s-nail » pour fournir « /usr/bin/mailx » (mailx) en mode automatique
Paramétrage de smartmontools (6.4+svn4214-1) ...
Traitement des actions différées (« triggers ») pour menu (2.1.47ubuntu1.16.04.1) ...
Traitement des actions différées (« triggers ») pour systemd (229-4ubuntu21.27) ...
Traitement des actions différées (« triggers ») pour ureadahead (0.100.0-19.1) ...
localepurge: Disk space freed in /usr/share/locale: 0 KiB
localepurge: Disk space freed in /usr/share/man: 0 KiB
localepurge: Disk space freed in /usr/share/gnome/help: 0 KiB
localepurge: Disk space freed in /usr/share/omf: 0 KiB
localepurge: Disk space freed in /usr/share/doc/kde/HTML: 0 KiB
Total disk space freed by localepurge: 0 KiB
harlocksama@TEXTORM974MB:~$ smartctl
smartctl 6.5 2016-01-24 r4214 [i686-linux-4.4.0-177-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
ERROR: smartctl requires a device name as the final command-line argument.
Use smartctl -h to get a usage summary
harlocksama@TEXTORM974MB:~$ sudo smartctl -a /dev/sda2
smartctl 6.5 2016-01-24 r4214 [i686-linux-4.4.0-177-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital VelociRaptor (AF)
Device Model: WDC WD5000HHTZ-04N21V0
Serial Number: WD-WX71E23LJC53
LU WWN Device Id: 5 0014ee 659157359
Firmware Version: 04.06A00
User Capacity: 500 107 862 016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 10000 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Thu Apr 23 13:30:47 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 4560) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 55) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x30bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 197 197 051 Pre-fail Always - 68270
3 Spin_Up_Time 0x0027 178 176 021 Pre-fail Always - 2091
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 464
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 6
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 029 029 000 Old_age Always - 52432
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 446
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 235
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 228
194 Temperature_Celsius 0x0022 119 101 000 Old_age Always - 28
196 Reallocated_Event_Count 0x0032 194 194 000 Old_age Always - 6
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 13
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 7
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 17
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 22
SMART Error Log Version: 1
Warning: ATA error count 9889 inconsistent with error log pointer 5
ATA Error Count: 9889 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 9889 occurred at disk power-on lifetime: 52432 hours (2184 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 10 b8 72 f9 e5 Error: UNC 16 sectors at LBA = 0x05f972b8 = 100233912
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 10 b0 72 f9 e5 08 13:30:16.935 READ DMA
c8 00 08 a8 72 f9 e5 08 13:30:16.918 READ DMA
c8 00 08 98 72 f9 e5 08 13:30:16.913 READ DMA
c8 00 08 88 72 f9 e5 08 13:30:16.913 READ DMA
c8 00 08 78 72 f9 e5 08 13:30:16.912 READ DMA
Error 9888 occurred at disk power-on lifetime: 52432 hours (2184 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 98 f7 f9 e5 Error: UNC 2 sectors at LBA = 0x05f9f798 = 100267928
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 02 98 f7 f9 e5 08 13:30:10.251 READ DMA
c8 00 08 90 f7 f9 e5 08 13:30:10.251 READ DMA
c8 00 40 d0 f7 f9 e5 08 13:30:10.239 READ DMA
ec 00 00 00 00 00 a0 08 13:30:10.229 IDENTIFY DEVICE
Error 9887 occurred at disk power-on lifetime: 52432 hours (2184 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 40 98 f7 f9 e5 Error: UNC 64 sectors at LBA = 0x05f9f798 = 100267928
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 90 f7 f9 e5 08 13:30:08.655 READ DMA
c8 00 40 50 f7 f9 e5 08 13:30:08.654 READ DMA
c8 00 40 10 f7 f9 e5 08 13:30:08.654 READ DMA
c8 00 40 d0 f6 f9 e5 08 13:30:08.654 READ DMA
c8 00 40 90 f6 f9 e5 08 13:30:08.653 READ DMA
Error 9886 occurred at disk power-on lifetime: 52432 hours (2184 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 80 c8 5f f9 e5 Error: UNC 128 sectors at LBA = 0x05f95fc8 = 100229064
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 80 b8 5f f9 e5 08 13:30:06.683 READ DMA
c8 00 04 84 5f f9 e5 08 13:30:06.683 READ DMA
c8 00 02 82 5f f9 e5 08 13:30:06.683 READ DMA
c8 00 02 80 5f f9 e5 08 13:30:06.683 READ DMA
c8 00 04 5c 5f f9 e5 08 13:30:06.683 READ DMA
Error 9885 occurred at disk power-on lifetime: 52432 hours (2184 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 60 98 5f f9 e5 Error: UNC 96 sectors at LBA = 0x05f95f98 = 100229016
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 60 58 5f f9 e5 08 13:30:05.169 READ DMA
c8 00 10 48 5f f9 e5 08 13:30:05.169 READ DMA
c8 00 08 40 5f f9 e5 08 13:30:05.169 READ DMA
c8 00 08 30 5f f9 e5 08 13:30:05.169 READ DMA
c8 00 08 20 5f f9 e5 08 13:30:05.168 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
harlocksama@TEXTORM974MB:~$
Edit: finalement j'ai réussi à mettre toute les informations demandées
