Sinon, Ubuntu vient de se réinstaller. Pour la 1e commande, j'ai ça :
total utilisé libre partagé tamp/cache disponible
Mem: 2,7Gi 1,1Gi 453Mi 56Mi 1,1Gi 1,4Gi
Partition d'échange: 2,0Gi 0B 2,0Gi
Pour la 2e commande après installation de l'utilitaire de gestion (je mets tout psq je sais pas du tout comment on lit ça...) :
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-33-generic] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.12
Device Model: ST3320418AS
Serial Number: 9VM3G4RA
LU WWN Device Id: 5 000c50 015be2e4e
Firmware Version: CC44
User Capacity: 320072933376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Thu Jun 4 18:30:18 2020 CEST
==> WARNING: A firmware update for this drive may be available,
see the following Seagate web pages:
http://knowledge.seagate.com/articles/e … Q/207931en
http://knowledge.seagate.com/articles/e … Q/213891en
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 617) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 74) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 113 099 006 Pre-fail Always - 54315643
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 098 098 020 Old_age Always - 2476
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 061 057 030 Pre-fail Always - 1679808713664
9 Power_On_Hours 0x0032 065 065 000 Old_age Always - 31051
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 020 Old_age Always - 2476
183 Runtime_Bad_Block 0x0000 100 100 000 Old_age Offline - 0
184 End-to-End_Error 0x0032 076 076 099 Old_age Always FAILING_NOW 24
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 8590065694
189 High_Fly_Writes 0x003a 096 096 000 Old_age Always - 4
190 Airflow_Temperature_Cel 0x0022 067 053 045 Old_age Always - 33 (Min/Max 21/34)
194 Temperature_Celsius 0x0022 033 047 000 Old_age Always - 33 (0 12 0 0 0)
195 Hardware_ECC_Recovered 0x001a 056 033 000 Old_age Always - 54315643
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 37396 (94 11 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 492092694
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 1316405749
SMART Error Log Version: 1
ATA Error Count: 4540 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 4540 occurred at disk power-on lifetime: 30824 hours (1284 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 81 87 80 40 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
2f 00 01 10 00 00 00 00 05:22:03.517 READ LOG EXT
60 00 40 eb 91 e3 41 00 05:22:03.516 READ FPDMA QUEUED
60 00 54 b0 5e f6 41 00 05:22:03.516 READ FPDMA QUEUED
60 00 38 02 04 06 42 00 05:22:03.516 READ FPDMA QUEUED
61 00 00 e8 b3 cb 4a 00 05:22:03.516 WRITE FPDMA QUEUED
Error 4539 occurred at disk power-on lifetime: 30824 hours (1284 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 81 87 80 40 Device Fault; Error: ABRT at LBA = 0x00808781 = 8423297
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 00 e8 b4 cb 4a 00 05:22:03.516 WRITE FPDMA QUEUED
00 00 00 00 00 00 00 ff 05:22:03.419 NOP [Abort queued commands]
61 00 0e 10 14 e8 48 00 05:22:03.387 WRITE FPDMA QUEUED
61 00 a0 f0 45 40 42 00 05:22:03.387 WRITE FPDMA QUEUED
61 00 01 f8 48 f3 41 00 05:22:03.387 WRITE FPDMA QUEUED
Error 4538 occurred at disk power-on lifetime: 30824 hours (1284 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 81 87 80 40 Device Fault; Error: ABRT at LBA = 0x00808781 = 8423297
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 40 eb 91 e3 41 00 05:22:03.386 READ FPDMA QUEUED
00 00 00 00 00 00 00 ff 05:22:03.340 NOP [Abort queued commands]
61 00 00 f8 5c fa 43 00 05:22:03.284 WRITE FPDMA QUEUED
61 00 00 f8 5d fa 43 00 05:22:03.284 WRITE FPDMA QUEUED
61 00 00 f8 5e fa 43 00 05:22:03.284 WRITE FPDMA QUEUED
Error 4537 occurred at disk power-on lifetime: 30824 hours (1284 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 81 87 80 40 Device Fault; Error: ABRT at LBA = 0x00808781 = 8423297
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 00 f0 ab cb 4a 00 05:22:03.283 WRITE FPDMA QUEUED
00 00 00 00 00 00 00 ff 05:22:03.185 NOP [Abort queued commands]
61 00 a0 f0 45 40 42 00 05:22:03.154 WRITE FPDMA QUEUED
61 00 01 f8 48 f3 41 00 05:22:03.154 WRITE FPDMA QUEUED
60 00 40 fa 41 1f 42 00 05:22:03.154 READ FPDMA QUEUED
Error 4536 occurred at disk power-on lifetime: 30824 hours (1284 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 81 87 80 40 Device Fault; Error: ABRT at LBA = 0x00808781 = 8423297
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 a8 4c 07 44 00 05:22:03.153 READ FPDMA QUEUED
00 00 00 00 00 00 00 ff 05:22:03.092 NOP [Abort queued commands]
61 00 00 f8 5b fa 43 00 05:22:03.092 WRITE FPDMA QUEUED
61 00 00 f8 5c fa 43 00 05:22:03.051 WRITE FPDMA QUEUED
61 00 00 f8 5d fa 43 00 05:22:03.051 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Merci et encore désolé pour mon incompréhension de... à peu près tout ^^
