Voilà, il est 16h43 et le PC fonctionne depuis 10 heures maintenant.
Cet après-midi, j'ai réalisé des sauvegardes sur un disque dur externe, basculé sur windows10 (toujours beaucoup d'appels disques avec ce système, je ne sais pas pourquoi), fait une mise à jour proposé par le gestionnaire de mise à jour après avoir rebasculé sur UBUNTU.
Voici à cette heure-là, la commande smartctl :
eric@eric-CQ1050FRm:~$ sudo smartctl -s on -a /dev/sda
[sudo] Mot de passe de eric :
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.3.0-62-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K1000.C
Device Model: Hitachi HDS721010CLA632
Serial Number: JP2940J81UHJ5V
LU WWN Device Id: 5 000cca 396d9af0c
Firmware Version: JP4OA41A
User Capacity: 1000204886016 bytes [1,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sun Jul 12 16:41:53 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (10047) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 167) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 094 016 Pre-fail Always - 0
2 Throughput_Performance 0x0027 135 100 054 Pre-fail Always - 97
3 Spin_Up_Time 0x0023 169 100 024 Pre-fail Always - 269 (Average 180)
4 Start_Stop_Count 0x0022 099 099 000 Old_age Always - 5332
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x002f 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 142 100 020 Pre-fail Offline - 29
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 5894
10 Spin_Retry_Count 0x0033 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 5331
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
185 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 65535
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 095 000 Old_age Always - 76554679
189 High_Fly_Writes 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 055 048 000 Old_age Always - 45 (Min/Max 25/47)
192 Power-Off_Retract_Count 0x0032 096 096 000 Old_age Always - 5333
193 Load_Cycle_Count 0x0032 096 096 000 Old_age Always - 5333
194 Temperature_Celsius 0x0002 133 115 000 Old_age Always - 45 (Min/Max 13/52)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
SMART Error Log Version: 0
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 5883 -
# 2 Short offline Interrupted (host reset) 10% 5623 -
# 3 Short offline Interrupted (host reset) 80% 5582 -
# 4 Short offline Completed without error 00% 5582 -
# 5 Short offline Interrupted (host reset) 70% 5576 -
# 6 Extended offline Interrupted (host reset) 90% 2 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
eric@eric-CQ1050FRm:~$
Qu'est-ce qu'a permis l'action sur les câbles d'alimentation et de données ? C'est cette manœuvre qui est à l'origine de cette amélioration mais pourquoi ?
Que faut-il faire d'autre à présent en fonction de la nouvelle analyse ?
