sudo smartctl -a /dev/sdf
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.4.0-42-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint M6
Device Model: SAMSUNG HM251JI
Serial Number: S19CJD0S166623
LU WWN Device Id: 5 0f0000 003166623
Firmware Version: 2SS00_01
User Capacity: 250,059,350,016 bytes [250 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS, ATA/ATAPI-7 T13/1532D revision 0
SATA Version is: SATA 2.5, 1.5 Gb/s
Local Time is: Mon Aug 3 23:03:07 2020 WAT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 87) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 87) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 9
3 Spin_Up_Time 0x0007 252 252 025 Pre-fail Always - 5375
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1829
5 Reallocated_Sector_Ct 0x0033 099 099 010 Pre-fail Always - 10
7 Seek_Error_Rate 0x000e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 252 252 000 Old_age Always - 0
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1792
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 2
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 1785
194 Temperature_Celsius 0x0022 142 142 000 Old_age Always - 32 (Min/Max 14/48)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 15
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 10
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x0032 252 252 000 Old_age Always - 0
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 380
225 Load_Cycle_Count 0x0032 095 095 000 Old_age Always - 55735
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
