Bonjour
Je ne sais pas si Je dois remettre cette discussion dans un autre post. Mais ceci est une suite à Mako 138 #20
Il ya donc des erreurs sous le disque mais...Je n'y comprends rien. Peut-être aussi parce que Je ne suis pas anglophone
E sur le #23, de geole, merci, J'iai voir.
carlos@nexus:~$ sudo smartctl -a /dev/sda
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.4.0-42-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, [url=http://www.smartmontools.org]www.smartmontools.org[/url]
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F3
Device Model: SAMSUNG HD502HJ
Serial Number: S20BJ9CZ401511
LU WWN Device Id: 5 0024e9 202357799
Firmware Version: 1AJ100E4
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Thu Aug 6 07:34:12 2020 WEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 4680) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 78) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 1
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 083 060 025 Pre-fail Always - 5290
4 Start_Stop_Count 0x0032 093 093 000 Old_age Always - 7770
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 10371
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 2
12 Power_Cycle_Count 0x0032 092 092 000 Old_age Always - 8144
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 2
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 064 048 000 Old_age Always - 33 (Min/Max 7/52)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 098 098 000 Old_age Always - 1141
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 3525
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 2
225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 8209
SMART Error Log Version: 1
ATA Error Count: 250 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 250 occurred at disk power-on lifetime: 8792 hours (366 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 00 c8 00 e0 Error: ABRT at LBA = 0x0000c800 = 51200
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c5 00 08 00 c8 53 e9 00 00:00:00.323 WRITE MULTIPLE
27 00 00 00 00 00 e0 00 00:00:00.323 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:00.323 IDENTIFY DEVICE
ef 03 08 00 00 00 a0 00 00:00:00.323 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:00:00.323 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 249 occurred at disk power-on lifetime: 8792 hours (366 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 00 c8 00 e0 Error: ABRT at LBA = 0x0000c800 = 51200
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c5 00 08 00 c8 53 e9 00 00:00:00.323 WRITE MULTIPLE
27 00 00 00 00 00 e0 00 00:00:00.323 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:00.323 IDENTIFY DEVICE
ef 03 08 00 00 00 a0 00 00:00:00.323 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:00:00.323 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 248 occurred at disk power-on lifetime: 8792 hours (366 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 00 c8 00 e0 Error: ABRT at LBA = 0x0000c800 = 51200
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c5 00 08 00 c8 53 e9 00 00:00:00.321 WRITE MULTIPLE
27 00 00 00 00 00 e0 00 00:00:00.321 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:00.321 IDENTIFY DEVICE
ef 03 08 00 00 00 a0 00 00:00:00.321 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:00:00.321 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 247 occurred at disk power-on lifetime: 8792 hours (366 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 00 c8 00 e0 Error: ABRT at LBA = 0x0000c800 = 51200
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c5 00 08 00 c8 53 e9 00 00:00:00.321 WRITE MULTIPLE
27 00 00 00 00 00 e0 00 00:00:00.321 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:00.321 IDENTIFY DEVICE
ef 03 08 00 00 00 a0 00 00:00:00.321 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:00:00.321 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 246 occurred at disk power-on lifetime: 8792 hours (366 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 00 c8 00 e0 Error: ABRT at LBA = 0x0000c800 = 51200
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c5 00 08 00 c8 53 e9 00 00:00:00.321 WRITE MULTIPLE
27 00 00 00 00 00 e0 00 00:00:00.321 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:00.321 IDENTIFY DEVICE
ef 03 08 00 00 00 a0 00 00:00:00.321 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:00:00.321 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 4287 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
carlos@nexus:~$
carlos@nexus:~$ sudo smartctl -a /dev/sda
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.4.0-42-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke,
www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F3
Device Model: SAMSUNG HD502HJ
Serial Number: S20BJ9CZ401511
LU WWN Device Id: 5 0024e9 202357799
Firmware Version: 1AJ100E4
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Thu Aug 6 07:34:12 2020 WEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 4680) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 78) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 1
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 083 060 025 Pre-fail Always - 5290
4 Start_Stop_Count 0x0032 093 093 000 Old_age Always - 7770
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 10371
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 2
12 Power_Cycle_Count 0x0032 092 092 000 Old_age Always - 8144
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 2
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 064 048 000 Old_age Always - 33 (Min/Max 7/52)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 098 098 000 Old_age Always - 1141
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 3525
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 2
225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 8209
SMART Error Log Version: 1
ATA Error Count: 250 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 250 occurred at disk power-on lifetime: 8792 hours (366 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 00 c8 00 e0 Error: ABRT at LBA = 0x0000c800 = 51200
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c5 00 08 00 c8 53 e9 00 00:00:00.323 WRITE MULTIPLE
27 00 00 00 00 00 e0 00 00:00:00.323 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:00.323 IDENTIFY DEVICE
ef 03 08 00 00 00 a0 00 00:00:00.323 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:00:00.323 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 249 occurred at disk power-on lifetime: 8792 hours (366 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 00 c8 00 e0 Error: ABRT at LBA = 0x0000c800 = 51200
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c5 00 08 00 c8 53 e9 00 00:00:00.323 WRITE MULTIPLE
27 00 00 00 00 00 e0 00 00:00:00.323 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:00.323 IDENTIFY DEVICE
ef 03 08 00 00 00 a0 00 00:00:00.323 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:00:00.323 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 248 occurred at disk power-on lifetime: 8792 hours (366 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 00 c8 00 e0 Error: ABRT at LBA = 0x0000c800 = 51200
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c5 00 08 00 c8 53 e9 00 00:00:00.321 WRITE MULTIPLE
27 00 00 00 00 00 e0 00 00:00:00.321 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:00.321 IDENTIFY DEVICE
ef 03 08 00 00 00 a0 00 00:00:00.321 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:00:00.321 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 247 occurred at disk power-on lifetime: 8792 hours (366 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 00 c8 00 e0 Error: ABRT at LBA = 0x0000c800 = 51200
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c5 00 08 00 c8 53 e9 00 00:00:00.321 WRITE MULTIPLE
27 00 00 00 00 00 e0 00 00:00:00.321 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:00.321 IDENTIFY DEVICE
ef 03 08 00 00 00 a0 00 00:00:00.321 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:00:00.321 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 246 occurred at disk power-on lifetime: 8792 hours (366 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 08 00 c8 00 e0 Error: ABRT at LBA = 0x0000c800 = 51200
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c5 00 08 00 c8 53 e9 00 00:00:00.321 WRITE MULTIPLE
27 00 00 00 00 00 e0 00 00:00:00.321 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:00.321 IDENTIFY DEVICE
ef 03 08 00 00 00 a0 00 00:00:00.321 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:00:00.321 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 4287 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
carlos@nexus:~$
