Salut,
Je recopie ici, le retour de ton rapport Smart :
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-47-generic] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA MQ04ABF100
Serial Number: Y7T9P44GT
LU WWN Device Id: 5 000039 822587dec
Firmware Version: JU001J
User Capacity: 1000204886016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu Sep 17 18:48:20 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 112) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 170) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1365
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 16726
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 1758
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 090 090 000 Old_age Always - 4069
10 Spin_Retry_Count 0x0033 253 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 3381
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 472
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 359
193 Load_Cycle_Count 0x0032 097 097 000 Old_age Always - 37112
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 46 (Min/Max 15/55)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 1758
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 112
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 253 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 091 091 000 Old_age Always - 3926
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 282
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 822 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 822 occurred at disk power-on lifetime: 4069 hours (169 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 38 18 96 1c 40 Error: UNC at LBA = 0x001c9618 = 1873432
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 38 18 96 1c 40 00 00:00:26.447 READ FPDMA QUEUED
ef 10 03 00 00 00 a0 00 00:00:26.446 SET FEATURES [Enable SATA feature]
ef 10 02 00 00 00 a0 00 00:00:26.446 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:00:26.445 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:26.443 IDENTIFY DEVICE
Error 821 occurred at disk power-on lifetime: 4069 hours (169 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 98 18 96 1c 40 Error: UNC at LBA = 0x001c9618 = 1873432
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 98 18 96 1c 40 00 00:00:25.703 READ FPDMA QUEUED
ef 10 03 00 00 00 a0 00 00:00:25.702 SET FEATURES [Enable SATA feature]
ef 10 02 00 00 00 a0 00 00:00:25.702 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:00:25.701 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:25.700 IDENTIFY DEVICE
Error 820 occurred at disk power-on lifetime: 4069 hours (169 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 a8 18 96 1c 40 Error: UNC at LBA = 0x001c9618 = 1873432
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 a8 18 96 1c 40 00 00:00:24.985 READ FPDMA QUEUED
60 20 a0 e8 95 1c 40 00 00:00:24.985 READ FPDMA QUEUED
60 08 98 e0 95 1c 40 00 00:00:24.984 READ FPDMA QUEUED
60 20 90 a8 95 1c 40 00 00:00:24.984 READ FPDMA QUEUED
60 08 88 a0 95 1c 40 00 00:00:24.983 READ FPDMA QUEUED
Error 819 occurred at disk power-on lifetime: 4069 hours (169 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 90 18 96 1c 40 Error: UNC at LBA = 0x001c9618 = 1873432
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 90 18 96 1c 40 00 00:00:13.335 READ FPDMA QUEUED
ef 10 03 00 00 00 a0 00 00:00:13.334 SET FEATURES [Enable SATA feature]
ef 10 02 00 00 00 a0 00 00:00:13.334 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:00:13.333 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:13.332 IDENTIFY DEVICE
Error 818 occurred at disk power-on lifetime: 4069 hours (169 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 b8 18 96 1c 40 Error: UNC at LBA = 0x001c9618 = 1873432
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 b8 18 96 1c 40 00 00:00:12.591 READ FPDMA QUEUED
ef 10 03 00 00 00 a0 00 00:00:12.590 SET FEATURES [Enable SATA feature]
ef 10 02 00 00 00 a0 00 00:00:12.590 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:00:12.589 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:12.588 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 00% 4069 976651504
# 2 Short offline Completed: read failure 00% 4069 976651504
# 3 Short offline Completed: read failure 00% 4069 976651504
# 4 Extended offline Aborted by host 90% 4069 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
On y repère ces lignes :
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 1758
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 472
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 1758
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 112
Il a eu 1758 secteurs réalloués et il en reste 112 qui n'ont pu être réalloués et qui sont donc perdus. Le disque à été bien secoués vu qu'il y a eu 472 chos et fortes vibrations. Pour conclure, ton disque est en train de lâcher. Il faut le remplacer.
A+
