Ce site est optimisé pour être consulté depuis un navigateur moderne dans lequel JavaScript est activé.

Clé usb impossible à formater

steph60400

bonjour,
Après 1 seule utilisation , ma clé USB ne fonctionne plus. C'est une clé qui est utilisée par la voiture Tesla pour enregistrer les films des caméras de la voiture.
On ne peut plus supprimer les fichiers.

J'ai utilisé Gparted mais il y a eu une erreur :

Erreur d'entrée/sortie lors de l'écriture sur dev/sdb1

Comment faire pour reformater la clé ?

merci

bluc

Bonjour

Pas de commutateur sur la clé ?,,,
Depuis le menu de gparted essaye Périphérique → Créer une table de partition

Sinon

sudo fdisk -l

geole

Bonsoir.
Donne aussi le retour de la commande.

dmesg | tail -100

steph60400

Bonjour,
voici les retours :
sudo fdisk -l :

Disque /dev/sda : 931,53 GiB, 1000204886016 octets, 1953525168 secteurs
Disk model: HGST HTS541010A9
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 4096 octets
taille d'E/S (minimale / optimale) : 4096 octets / 4096 octets
Type d'étiquette de disque : gpt
Identifiant de disque : 14102C5E-5B20-492F-803A-F508192B6745

Périphérique Début Fin Secteurs Taille Type
/dev/sda1 2048 1050623 1048576 512M Système EFI
/dev/sda2 1050624 1953523711 1952473088 931G Système de fichiers Linux

Disque /dev/sdb : 117,43 GiB, 126079198208 octets, 246248434 secteurs
Disk model: Cruzer Blade
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 512 octets
taille d'E/S (minimale / optimale) : 512 octets / 512 octets
Type d'étiquette de disque : dos
Identifiant de disque : 0x0bae63c1

Périphérique Amorçage Début Fin Secteurs Taille Id Type
/dev/sdb1 2048 246248433 246246386 117,4G 7 HPFS/NTFS/exFAT

et pour la commande
dmesg | tail -100

[ 349.719317] blk_update_request: I/O error, dev sdb, sector 2536 op 0x1:(WRITE) flags 0x104000 phys_seg 120 prio class 0
[ 349.866385] usb 1-1: new high-speed USB device number 6 using xhci_hcd
[ 355.097700] usb 1-1: device descriptor read/64, error -110
[ 370.706712] usb 1-1: device descriptor read/64, error -110
[ 370.942565] usb 1-1: new high-speed USB device number 7 using xhci_hcd
[ 376.082019] usb 1-1: device descriptor read/64, error -110
[ 391.699756] usb 1-1: device descriptor read/64, error -110
[ 391.807851] usb usb1-port1: attempt power cycle
[ 392.463424] usb 1-1: new high-speed USB device number 8 using xhci_hcd
[ 397.711133] usb 1-1: device descriptor read/8, error -110
[ 403.085963] usb 1-1: device descriptor read/8, error -110
[ 403.321971] usb 1-1: new high-speed USB device number 9 using xhci_hcd
[ 408.461440] usb 1-1: device descriptor read/8, error -110
[ 413.836752] usb 1-1: device descriptor read/8, error -110
[ 413.944766] usb usb1-port1: unable to enumerate USB device
[ 549.631206] usb 1-1: new high-speed USB device number 10 using xhci_hcd
[ 549.780215] usb 1-1: New USB device found, idVendor=0781, idProduct=5567, bcdDevice= 1.00
[ 549.780233] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 549.780245] usb 1-1: Product: Cruzer Blade
[ 549.780256] usb 1-1: Manufacturer: SanDisk
[ 549.780265] usb 1-1: SerialNumber: 4C530000151102105515
[ 549.782771] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 549.785919] scsi host2: usb-storage 1-1:1.0
[ 550.790206] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Blade 1.00 PQ: 0 ANSI: 6
[ 550.797581] scsi 2:0:0:0: Attached scsi generic sg2 type 0
[ 550.800268] sd 2:0:0:0: [sdb] 246248434 512-byte logical blocks: (126 GB/117 GiB)
[ 550.801128] sd 2:0:0:0: [sdb] Write Protect is off
[ 550.801138] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 550.801618] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 550.840829] sdb: sdb1
[ 550.846528] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 1207.619287] ata1.00: exception Emask 0x10 SAct 0x80000000 SErr 0x2d0100 action 0x6 frozen
[ 1207.619318] ata1.00: irq_stat 0x08000000, interface fatal error
[ 1207.619339] ata1: SError: { UnrecovData PHYRdyChg CommWake 10B8B BadCRC }
[ 1207.619359] ata1.00: failed command: READ FPDMA QUEUED
[ 1207.619393] ata1.00: cmd 60/10:f8:c0:6f:95/00:00:5a:00:00/40 tag 31 ncq dma 8192 in
res 50/00:10:c0:6f:95/00:00:5a:00:00/40 Emask 0x10 (ATA bus error)
[ 1207.619406] ata1.00: status: { DRDY }
[ 1207.619426] ata1: hard resetting link
[ 1207.932882] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1207.976156] ata1.00: configured for UDMA/133
[ 1207.976522] sd 0:0:0:0: [sda] tag#31 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 1207.976545] sd 0:0:0:0: [sda] tag#31 Sense Key : Illegal Request [current]
[ 1207.976560] sd 0:0:0:0: [sda] tag#31 Add. Sense: Unaligned write command
[ 1207.976579] sd 0:0:0:0: [sda] tag#31 CDB: Read(10) 28 00 5a 95 6f c0 00 00 10 00
[ 1207.976588] print_req_error: 20 callbacks suppressed
[ 1207.976607] blk_update_request: I/O error, dev sda, sector 1519742912 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 1207.976753] ata1: EH complete
[11784.376644] ata1.00: exception Emask 0x10 SAct 0x8000 SErr 0x2d0100 action 0x6 frozen
[11784.376651] ata1.00: irq_stat 0x08000000, interface fatal error
[11784.376655] ata1: SError: { UnrecovData PHYRdyChg CommWake 10B8B BadCRC }
[11784.376659] ata1.00: failed command: READ FPDMA QUEUED
[11784.376666] ata1.00: cmd 60/00:78:e0:1f:f6/01:00:00:00:00/40 tag 15 ncq dma 131072 in
res 50/00:00:e0:1f:f6/00:01:00:00:00/40 Emask 0x10 (ATA bus error)
[11784.376669] ata1.00: status: { DRDY }
[11784.376674] ata1: hard resetting link
[11784.691344] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[11784.740020] ata1.00: configured for UDMA/133
[11784.740695] sd 0:0:0:0: [sda] tag#15 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[11784.740715] sd 0:0:0:0: [sda] tag#15 Sense Key : Illegal Request [current]
[11784.740731] sd 0:0:0:0: [sda] tag#15 Add. Sense: Unaligned write command
[11784.740760] sd 0:0:0:0: [sda] tag#15 CDB: Read(10) 28 00 00 f6 1f e0 00 01 00 00
[11784.740777] blk_update_request: I/O error, dev sda, sector 16130016 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0
[11784.740915] ata1: EH complete
[11802.702849] perf: interrupt took too long (2521 > 2500), lowering kernel.perf_event_max_sample_rate to 79250
[21993.728650] perf: interrupt took too long (3240 > 3151), lowering kernel.perf_event_max_sample_rate to 61500
[34624.393062] perf: interrupt took too long (4062 > 4050), lowering kernel.perf_event_max_sample_rate to 49000
[61973.502042] perf: interrupt took too long (5093 > 5077), lowering kernel.perf_event_max_sample_rate to 39250
[79688.875923] perf: interrupt took too long (6380 > 6366), lowering kernel.perf_event_max_sample_rate to 31250
[136435.974680] perf: interrupt took too long (8001 > 7975), lowering kernel.perf_event_max_sample_rate to 24750
[176985.051240] usb 1-1: USB disconnect, device number 10
[176989.829669] usb 1-1: new high-speed USB device number 11 using xhci_hcd
[176989.984361] usb 1-1: New USB device found, idVendor=0781, idProduct=5567, bcdDevice= 1.00
[176989.984379] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[176989.984393] usb 1-1: Product: Cruzer Blade
[176989.984403] usb 1-1: Manufacturer: SanDisk
[176989.984412] usb 1-1: SerialNumber: 4C530000151102105515
[176989.987833] usb-storage 1-1:1.0: USB Mass Storage device detected
[176989.990459] scsi host2: usb-storage 1-1:1.0
[176991.008133] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Blade 1.00 PQ: 0 ANSI: 6
[176991.012234] sd 2:0:0:0: Attached scsi generic sg2 type 0
[176991.014789] sd 2:0:0:0: [sdb] 246248434 512-byte logical blocks: (126 GB/117 GiB)
[176991.015583] sd 2:0:0:0: [sdb] Write Protect is off
[176991.015596] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00
[176991.016130] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[176991.051428] sdb: sdb1
[176991.057264] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[176991.694094] [EXFAT] trying to mount...
[176992.022202] [EXFAT] mounted successfully
[177016.084883] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[177016.094556] ata2.00: configured for UDMA/133
[177233.374816] usb 1-2: new low-speed USB device number 12 using xhci_hcd
[177233.527118] usb 1-2: New USB device found, idVendor=046d, idProduct=c016, bcdDevice= 3.40
[177233.527122] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[177233.527125] usb 1-2: Product: Optical USB Mouse
[177233.527127] usb 1-2: Manufacturer: Logitech
[177233.847862] usbcore: registered new interface driver usbhid
[177233.847865] usbhid: USB HID core driver
[177234.000620] input: Logitech Optical USB Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/0003:046D:C016.0001/input/input12
[177234.059153] hid-generic 0003:046D:C016.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:14.0-2/input0

Merci de votre aide

geole

Pour la clé USB, c'est un peu ce que je pensais.

[176991.051428]  sdb: sdb1
[176991.057264] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[176991.694094] [EXFAT] trying to mount...
[176992.022202] [EXFAT] mounted successfully

~~donc li faut installer EXFAT~~ A priori il est installé...

Pour formater, il faudra utiliser gnome disk utility pour conserver ce format et faire un formatage lent afin de traiter ce problème

[  349.719317] blk_update_request: I/O error, dev sdb, sector 2536 op 0x1:(WRITE) flags 0x104000 phys_seg 120 prio class 0

Tu vas en profiter pour installer smartmontools
et donner le retour de cette commande

sudo smartctl -s on -a /dev/sda

afin de traiter ce problème

[11784.740715] sd 0:0:0:0: [sda] tag#15 Sense Key : Illegal Request [current]
[11784.740731] sd 0:0:0:0: [sda] tag#15 Add. Sense: Unaligned write command
[11784.740760] sd 0:0:0:0: [sda] tag#15 CDB: Read(10) 28 00 00 f6 1f e0 00 01 00 00
[11784.740777] blk_update_request: I/O error, dev sda, sector 16130016 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0

steph60400

Merci pour ces réponses.
Je m'en occupe ce matin
cdt et bonne journée

steph60400

Bonjour,
J'ai tenté de formaté la clé avec gnome-disks mais cela n'a pas abouti.
Le message d'erreur est le suivant :

Erreur lors du formatage du volume
Error synchronizing after initial wipe : time out waiting for object ( udisk-error-quark,0)

Je vais maintenant installer smartmontools.

bonne journée