Bon apparemment mon disque contient des erreurs :
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-60-generic] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 7200.5
Device Model: ST9750422AS
Serial Number: 6WS1G1WF
LU WWN Device Id: 5 000c50 046f963ef
Firmware Version: 0001BSM1
User Capacity: 750,156,374,016 bytes [750 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sun Jan 10 16:21:44 2021 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 145) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 108 094 006 - 190844816
3 Spin_Up_Time PO---- 100 100 000 - 0
4 Start_Stop_Count -O--CK 098 098 020 - 2253
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0
7 Seek_Error_Rate POSR-- 085 060 030 - 358447642
9 Power_On_Hours -O--CK 026 026 000 - 64888
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 100 100 020 - 872
184 End-to-End_Error -O--CK 100 100 099 - 0
187 Reported_Uncorrect -O--CK 001 001 000 - 209
188 Command_Timeout -O--CK 100 090 000 - 227636740162
189 High_Fly_Writes -O-RCK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 060 046 045 - 40 (Min/Max 18/41)
191 G-Sense_Error_Rate -O--CK 100 100 000 - 0
192 Power-Off_Retract_Count -O--CK 099 099 000 - 2002
193 Load_Cycle_Count -O--CK 085 085 000 - 30994
194 Temperature_Celsius -O---K 040 054 000 - 40 (0 13 0 0 0)
195 Hardware_ECC_Recovered -O-RC- 118 099 000 - 190844816
197 Current_Pending_Sector -O--C- 100 098 000 - 0
198 Offline_Uncorrectable ----C- 100 098 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0
240 Head_Flying_Hours ------ 100 253 000 - 64759 (160 245 0)
241 Total_LBAs_Written ------ 100 253 000 - 2648475608
242 Total_LBAs_Read ------ 100 253 000 - 3195122231
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 GPL,SL R/O 1 Summary SMART error log
0x02 GPL,SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 5 Ext. Comprehensive SMART error log
0x06 GPL,SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 GPL,SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa1 GPL,SL VS 20 Device vendor specific log
0xa2 GPL VS 2248 Device vendor specific log
0xa8 GPL,SL VS 65 Device vendor specific log
0xa9 GPL,SL VS 1 Device vendor specific log
0xab GPL VS 1 Device vendor specific log
0xae GPL VS 1 Device vendor specific log
0xb0 GPL VS 2864 Device vendor specific log
0xbd GPL VS 252 Device vendor specific log
0xbe-0xbf GPL VS 65535 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 207 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 207 [6] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 03 01 0c 60 00 00 Error: UNC at LBA = 0x03010c60 = 50400352
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 03 01 0c 60 40 00 00:09:05.904 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:09:05.903 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:09:05.903 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:09:05.902 IDENTIFY DEVICE
ef 00 90 00 06 00 00 00 00 00 00 00 00 00:09:05.902 SET FEATURES [Disable SATA feature]
Error 206 [5] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 03 01 0c 60 00 00 Error: UNC at LBA = 0x03010c60 = 50400352
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 03 01 0c 60 40 00 00:09:02.870 READ FPDMA QUEUED
60 00 00 00 08 00 00 03 01 0c 38 40 00 00:09:01.527 READ FPDMA QUEUED
60 00 00 00 08 00 00 03 01 0c 30 40 00 00:09:01.503 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:09:01.502 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:09:01.502 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 205 [4] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 03 01 0c 28 00 00 Error: UNC at LBA = 0x03010c28 = 50400296
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 03 01 0c 28 40 00 00:08:58.532 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:08:58.531 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:08:58.531 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:08:58.530 IDENTIFY DEVICE
ef 00 90 00 06 00 00 00 00 00 00 00 00 00:08:58.530 SET FEATURES [Disable SATA feature]
Error 204 [3] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 03 01 0c 28 00 00 Error: UNC at LBA = 0x03010c28 = 50400296
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 03 01 0c 28 40 00 00:08:55.576 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:08:55.575 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:08:55.574 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:08:55.574 IDENTIFY DEVICE
ef 00 90 00 06 00 00 00 00 00 00 00 00 00:08:55.573 SET FEATURES [Disable SATA feature]
Error 203 [2] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 03 01 0c 20 00 00 Error: UNC at LBA = 0x03010c20 = 50400288
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 03 01 0c 20 40 00 00:08:52.471 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:08:52.470 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:08:52.470 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:08:52.469 IDENTIFY DEVICE
ef 00 90 00 06 00 00 00 00 00 00 00 00 00:08:52.469 SET FEATURES [Disable SATA feature]
Error 202 [1] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 03 01 0c 20 00 00 Error: UNC at LBA = 0x03010c20 = 50400288
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 03 01 0c 20 40 00 00:08:49.170 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:08:49.169 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:08:49.168 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:08:49.168 IDENTIFY DEVICE
ef 00 90 00 06 00 00 00 00 00 00 00 00 00:08:49.168 SET FEATURES [Disable SATA feature]
Error 201 [0] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 03 01 0c 18 00 00 Error: WP at LBA = 0x03010c18 = 50400280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 00 00 08 00 00 05 c0 12 b8 40 00 00:08:46.120 WRITE FPDMA QUEUED
61 00 00 00 10 00 00 02 c0 09 00 40 00 00:08:46.120 WRITE FPDMA QUEUED
61 00 00 00 08 00 00 01 01 3b 28 40 00 00:08:46.119 WRITE FPDMA QUEUED
61 00 00 00 08 00 00 01 01 3b 00 40 00 00:08:46.118 WRITE FPDMA QUEUED
60 00 00 00 08 00 00 03 01 0c 18 40 00 00:08:46.117 READ FPDMA QUEUED
Error 200 [19] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 03 01 0c 18 00 00 Error: UNC at LBA = 0x03010c18 = 50400280
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 03 01 0c 18 40 00 00:08:43.136 READ FPDMA QUEUED
60 00 00 00 08 00 00 03 01 0c 10 40 00 00:08:43.135 READ FPDMA QUEUED
60 00 00 00 08 00 00 03 01 0c 08 40 00 00:08:43.115 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:08:43.114 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:08:43.113 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 199 [18] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 03 01 0c 00 00 00 Error: UNC at LBA = 0x03010c00 = 50400256
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 03 01 0c 00 40 00 00:08:40.150 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:08:40.150 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:08:40.150 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:08:40.149 IDENTIFY DEVICE
ef 00 90 00 06 00 00 00 00 00 00 00 00 00:08:40.149 SET FEATURES [Disable SATA feature]
Error 198 [17] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 03 01 0c 00 00 00 Error: UNC at LBA = 0x03010c00 = 50400256
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 03 01 0c 00 40 00 00:08:37.136 READ FPDMA QUEUED
60 00 00 00 08 00 00 03 01 0b f8 40 00 00:08:35.703 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:08:35.703 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:08:35.703 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:08:35.702 IDENTIFY DEVICE
Error 197 [16] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 03 01 0b f8 00 00 Error: UNC at LBA = 0x03010bf8 = 50400248
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 03 01 0b f8 40 00 00:08:32.624 READ FPDMA QUEUED
60 00 00 00 08 00 00 03 01 0b f0 40 00 00:08:31.195 READ FPDMA QUEUED
60 00 00 00 08 00 00 03 01 0b c8 40 00 00:08:31.079 READ FPDMA QUEUED
60 00 00 00 08 00 00 03 01 0b c0 40 00 00:08:31.072 READ FPDMA QUEUED
60 00 00 00 08 00 00 02 c1 3b 18 40 00 00:08:31.048 READ FPDMA QUEUED
Error 196 [15] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 03 01 0b f0 00 00 Error: UNC at LBA = 0x03010bf0 = 50400240
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 03 81 13 a8 40 00 00:08:27.372 READ FPDMA QUEUED
60 00 00 01 00 00 00 03 81 12 a0 40 00 00:08:27.370 READ FPDMA QUEUED
60 00 00 00 a0 00 00 03 81 11 d8 40 00 00:08:27.367 READ FPDMA QUEUED
60 00 00 00 10 00 00 03 81 10 f0 40 00 00:08:27.365 READ FPDMA QUEUED
60 00 00 00 88 00 00 03 81 10 60 40 00 00:08:27.365 READ FPDMA QUEUED
Error 195 [14] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 01 00 0d 90 00 00 Error: UNC at LBA = 0x01000d90 = 16780688
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 01 00 0d 90 40 00 00:08:09.660 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:08:09.660 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:08:09.659 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:08:09.659 IDENTIFY DEVICE
ef 00 90 00 06 00 00 00 00 00 00 00 00 00:08:09.658 SET FEATURES [Disable SATA feature]
Error 194 [13] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 01 00 0d 90 00 00 Error: UNC at LBA = 0x01000d90 = 16780688
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 01 00 0d 90 40 00 00:08:06.682 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:08:06.682 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:08:06.681 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:08:06.681 IDENTIFY DEVICE
ef 00 90 00 06 00 00 00 00 00 00 00 00 00:08:06.681 SET FEATURES [Disable SATA feature]
Error 193 [12] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 01 00 0d 90 00 00 Error: UNC at LBA = 0x01000d90 = 16780688
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 01 00 0d 90 40 00 00:08:03.623 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:08:03.623 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:08:03.622 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:08:03.622 IDENTIFY DEVICE
ef 00 90 00 06 00 00 00 00 00 00 00 00 00:08:03.622 SET FEATURES [Disable SATA feature]
Error 192 [11] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 01 00 0d 90 00 00 Error: UNC at LBA = 0x01000d90 = 16780688
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 01 00 0d 90 40 00 00:08:00.669 READ FPDMA QUEUED
60 00 00 00 08 00 00 01 00 0d 88 40 00 00:08:00.669 READ FPDMA QUEUED
60 00 00 00 08 00 00 01 00 0d 80 40 00 00:08:00.669 READ FPDMA QUEUED
60 00 00 00 08 00 00 01 04 28 d0 40 00 00:08:00.661 READ FPDMA QUEUED
60 00 00 00 08 00 00 01 04 28 d8 40 00 00:08:00.649 READ FPDMA QUEUED
Error 191 [10] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 01 00 09 d0 00 00 Error: UNC at LBA = 0x010009d0 = 16779728
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 01 00 09 d0 40 00 00:07:57.132 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:07:57.132 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:07:57.131 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:07:57.131 IDENTIFY DEVICE
ef 00 90 00 06 00 00 00 00 00 00 00 00 00:07:57.131 SET FEATURES [Disable SATA feature]
Error 190 [9] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 01 00 09 d0 00 00 Error: UNC at LBA = 0x010009d0 = 16779728
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 01 00 09 d0 40 00 00:07:53.724 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:07:53.724 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:07:53.723 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:07:53.723 IDENTIFY DEVICE
ef 00 90 00 06 00 00 00 00 00 00 00 00 00:07:53.723 SET FEATURES [Disable SATA feature]
Error 189 [8] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 01 00 09 d0 00 00 Error: UNC at LBA = 0x010009d0 = 16779728
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 01 00 09 d0 40 00 00:07:50.536 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:07:50.536 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:07:50.535 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:07:50.535 IDENTIFY DEVICE
ef 00 90 00 06 00 00 00 00 00 00 00 00 00:07:50.535 SET FEATURES [Disable SATA feature]
Error 188 [7] occurred at disk power-on lifetime: 64573 hours (2690 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 01 00 09 d0 00 00 Error: UNC at LBA = 0x010009d0 = 16779728
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 01 00 09 d0 40 00 00:07:47.156 READ FPDMA QUEUED
60 00 00 00 08 00 00 01 00 09 c8 40 00 00:07:47.155 READ FPDMA QUEUED
60 00 00 00 08 00 00 01 00 09 c0 40 00 00:07:47.155 READ FPDMA QUEUED
60 00 00 00 08 00 00 01 00 09 b8 40 00 00:07:47.154 READ FPDMA QUEUED
60 00 00 00 08 00 00 01 00 09 b0 40 00 00:07:47.154 READ FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 522 (0x020a)
Device State: Active (0)
Current Temperature: 40 Celsius
Power Cycle Min/Max Temperature: 18/41 Celsius
Lifetime Min/Max Temperature: 13/54 Celsius
Specified Max Operating Temperature: 42 Celsius
Under/Over Temperature Limit Count: 0/275
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/ 0 Celsius
Min/Max Temperature Limit: 0/ 0 Celsius
Temperature History Size (Index): 128 (22)
Index Estimated Time Temperature Celsius
23 2021-01-10 14:14 40 *********************
24 2021-01-10 14:15 40 *********************
25 2021-01-10 14:16 40 *********************
26 2021-01-10 14:17 41 **********************
... ..( 80 skipped). .. **********************
107 2021-01-10 15:38 41 **********************
108 2021-01-10 15:39 40 *********************
... ..( 19 skipped). .. *********************
0 2021-01-10 15:59 40 *********************
1 2021-01-10 16:00 39 ********************
... ..( 18 skipped). .. ********************
20 2021-01-10 16:19 39 ********************
21 2021-01-10 16:20 40 *********************
22 2021-01-10 16:21 40 *********************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 14 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
En même temps il a presque 10 ans le garçon !
Qu'en pensez-vous ?
