Bonsoir,
je viens d'installer smartctl avec pop up d'avertissement
et comme je viens d'en recevoir un ("8 Currently unreadable (pending) sectors") je vous met le résultat
je viens d'installer smartctl avec pop up d'avertissement
et comme je viens d'en recevoir un ("8 Currently unreadable (pending) sectors") je vous met le résultat
sudo smartctl -s on -a /dev/sda
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-65-generic] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi/HGST Travelstar Z5K500
Device Model: HGST HTS545050A7E680
Serial Number: TMA55C3J0JS9XM
LU WWN Device Id: 5 000cca 7dec79d7a
Firmware Version: GG2OAF10
User Capacity: 500107862016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu Feb 18 22:46:30 2021 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 45) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 120) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0
3 Spin_Up_Time 0x0007 206 206 033 Pre-fail Always - 1
4 Start_Stop_Count 0x0012 097 097 000 Old_age Always - 4893
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0
9 Power_On_Hours 0x0012 087 087 000 Old_age Always - 5991
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1395
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 12
193 Load_Cycle_Count 0x0012 092 092 000 Old_age Always - 87763
194 Temperature_Celsius 0x0002 162 162 000 Old_age Always - 37 (Min/Max 11/48)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 3
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 8
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 2
223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 114 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 114 occurred at disk power-on lifetime: 1525 hours (63 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 83 a1 bd 02 Error: UNC at LBA = 0x02bda183 = 45982083
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 00 01 83 a1 bd 40 00 01:49:03.275 READ VERIFY SECTOR(S) EXT
42 00 01 82 a1 bd 40 00 01:48:59.842 READ VERIFY SECTOR(S) EXT
42 00 01 81 a1 bd 40 00 01:48:56.409 READ VERIFY SECTOR(S) EXT
42 00 01 80 a1 bd 40 00 01:48:52.975 READ VERIFY SECTOR(S) EXT
42 00 02 86 a1 bd 40 00 01:48:49.542 READ VERIFY SECTOR(S) EXT
Error 113 occurred at disk power-on lifetime: 1525 hours (63 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 82 a1 bd 02 Error: UNC at LBA = 0x02bda182 = 45982082
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 00 01 82 a1 bd 40 00 01:48:59.842 READ VERIFY SECTOR(S) EXT
42 00 01 81 a1 bd 40 00 01:48:56.409 READ VERIFY SECTOR(S) EXT
42 00 01 80 a1 bd 40 00 01:48:52.975 READ VERIFY SECTOR(S) EXT
42 00 02 86 a1 bd 40 00 01:48:49.542 READ VERIFY SECTOR(S) EXT
42 00 02 84 a1 bd 40 00 01:48:46.108 READ VERIFY SECTOR(S) EXT
Error 112 occurred at disk power-on lifetime: 1525 hours (63 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 81 a1 bd 02 Error: UNC at LBA = 0x02bda181 = 45982081
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 00 01 81 a1 bd 40 00 01:48:56.409 READ VERIFY SECTOR(S) EXT
42 00 01 80 a1 bd 40 00 01:48:52.975 READ VERIFY SECTOR(S) EXT
42 00 02 86 a1 bd 40 00 01:48:49.542 READ VERIFY SECTOR(S) EXT
42 00 02 84 a1 bd 40 00 01:48:46.108 READ VERIFY SECTOR(S) EXT
42 00 02 82 a1 bd 40 00 01:48:42.675 READ VERIFY SECTOR(S) EXT
Error 111 occurred at disk power-on lifetime: 1525 hours (63 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 80 a1 bd 02 Error: UNC at LBA = 0x02bda180 = 45982080
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 00 01 80 a1 bd 40 00 01:48:52.975 READ VERIFY SECTOR(S) EXT
42 00 02 86 a1 bd 40 00 01:48:49.542 READ VERIFY SECTOR(S) EXT
42 00 02 84 a1 bd 40 00 01:48:46.108 READ VERIFY SECTOR(S) EXT
42 00 02 82 a1 bd 40 00 01:48:42.675 READ VERIFY SECTOR(S) EXT
42 00 02 80 a1 bd 40 00 01:48:39.230 READ VERIFY SECTOR(S) EXT
Error 110 occurred at disk power-on lifetime: 1525 hours (63 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 86 a1 bd 02 Error: UNC at LBA = 0x02bda186 = 45982086
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 00 02 86 a1 bd 40 00 01:48:49.542 READ VERIFY SECTOR(S) EXT
42 00 02 84 a1 bd 40 00 01:48:46.108 READ VERIFY SECTOR(S) EXT
42 00 02 82 a1 bd 40 00 01:48:42.675 READ VERIFY SECTOR(S) EXT
42 00 02 80 a1 bd 40 00 01:48:39.230 READ VERIFY SECTOR(S) EXT
42 00 04 84 a1 bd 40 00 01:48:35.786 READ VERIFY SECTOR(S) EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 5991 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
en vous remerciant d'avance de votre interpretation des résultats