Alors...
dmesg
donne :
[ 4.068573] Scanning for low memory corruption every 60 seconds
[ 4.068853] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 4.068875] Initialise system trusted keyring
[ 4.068892] audit: initializing netlink subsys (disabled)
[ 4.068902] audit: type=2000 audit(1468704278.044:1): initialized
[ 4.069209] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 4.070385] zpool: loaded
[ 4.070387] zbud: loaded
[ 4.070518] VFS: Disk quotas dquot_6.5.2
[ 4.070545] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 4.070888] fuse init (API version 7.23)
[ 4.070993] Key type big_key registered
[ 4.071304] Key type asymmetric registered
[ 4.071306] Asymmetric key parser 'x509' registered
[ 4.071333] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 4.071371] io scheduler noop registered
[ 4.071373] io scheduler deadline registered (default)
[ 4.071396] io scheduler cfq registered
[ 4.071939] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 4.071951] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 4.071975] efifb: probing for efifb
[ 4.071993] efifb: framebuffer at 0xc0000000, mapped to 0xffffc90010f00000, using 8128k, total 8128k
[ 4.071995] efifb: mode is 1920x1080x32, linelength=7680, pages=1
[ 4.071995] efifb: scrolling: redraw
[ 4.071996] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 4.072070] Console: switching to colour frame buffer device 240x67
[ 4.072088] fb0: EFI VGA frame buffer device
[ 4.072095] intel_idle: MWAIT substates: 0x42120
[ 4.072096] intel_idle: v0.4 model 0x3C
[ 4.072097] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 4.072400] ACPI: AC Adapter [ACAD] (on-line)
[ 4.072479] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/PNP0C0C:00/input/input0
[ 4.072482] ACPI: Power Button [PWRB]
[ 4.072509] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/PNP0C0E:00/input/input1
[ 4.072511] ACPI: Sleep Button [SLPB]
[ 4.072545] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
[ 4.072557] ACPI: Lid Switch [LID0]
[ 4.072584] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 4.072585] ACPI: Power Button [PWRF]
[ 4.073533] thermal LNXTHERM:00: registered as thermal_zone0
[ 4.073534] ACPI: Thermal Zone [TZ00] (64 C)
[ 4.073572] GHES: HEST is not enabled!
[ 4.073676] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 4.154347] ACPI: Battery Slot [BAT1] (battery present)
[ 4.154489] Linux agpgart interface v0.103
[ 4.155660] brd: module loaded
[ 4.156216] loop: module loaded
[ 4.156402] libphy: Fixed MDIO Bus: probed
[ 4.156405] tun: Universal TUN/TAP device driver, 1.6
[ 4.156405] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 4.156467] PPP generic driver version 2.4.2
[ 4.156664] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 4.156669] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[ 4.157772] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 4.157859] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.157860] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.157861] usb usb1: Product: xHCI Host Controller
[ 4.157863] usb usb1: Manufacturer: Linux 3.19.0-65-generic xhci-hcd
[ 4.157870] usb usb1: SerialNumber: 0000:00:14.0
[ 4.157966] hub 1-0:1.0: USB hub found
[ 4.157982] hub 1-0:1.0: 14 ports detected
[ 4.161167] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 4.161170] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 4.161208] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 4.161209] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.161210] usb usb2: Product: xHCI Host Controller
[ 4.161211] usb usb2: Manufacturer: Linux 3.19.0-65-generic xhci-hcd
[ 4.161212] usb usb2: SerialNumber: 0000:00:14.0
[ 4.161296] hub 2-0:1.0: USB hub found
[ 4.161314] hub 2-0:1.0: 6 ports detected
[ 4.162333] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.162348] ehci-pci: EHCI PCI platform driver
[ 4.162447] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 4.162451] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 4.162469] ehci-pci 0000:00:1a.0: debug port 2
[ 4.166361] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[ 4.166373] ehci-pci 0000:00:1a.0: irq 21, io mem 0xd171d000
[ 4.178297] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 4.178357] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.178359] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.178360] usb usb3: Product: EHCI Host Controller
[ 4.178361] usb usb3: Manufacturer: Linux 3.19.0-65-generic ehci_hcd
[ 4.178362] usb usb3: SerialNumber: 0000:00:1a.0
[ 4.178537] hub 3-0:1.0: USB hub found
[ 4.178543] hub 3-0:1.0: 2 ports detected
[ 4.178810] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 4.178815] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 4
[ 4.178826] ehci-pci 0000:00:1d.0: debug port 2
[ 4.182737] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 4.182750] ehci-pci 0000:00:1d.0: irq 23, io mem 0xd171c000
[ 4.194307] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 4.194375] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.194377] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.194378] usb usb4: Product: EHCI Host Controller
[ 4.194380] usb usb4: Manufacturer: Linux 3.19.0-65-generic ehci_hcd
[ 4.194381] usb usb4: SerialNumber: 0000:00:1d.0
[ 4.194555] hub 4-0:1.0: USB hub found
[ 4.194560] hub 4-0:1.0: 2 ports detected
[ 4.194703] ehci-platform: EHCI generic platform driver
[ 4.194716] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.194721] ohci-pci: OHCI PCI platform driver
[ 4.194731] ohci-platform: OHCI generic platform driver
[ 4.194745] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.194800] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:MSS2] at 0x60,0x64 irq 1,12
[ 4.219187] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 4.219190] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 4.219455] mousedev: PS/2 mouse device common for all mice
[ 4.219944] rtc_cmos 00:02: RTC can wake from S4
[ 4.220091] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 4.220118] rtc_cmos 00:02: alarms up to one month, 242 bytes nvram, hpet irqs
[ 4.220131] i2c /dev entries driver
[ 4.220191] device-mapper: uevent: version 1.0.3
[ 4.220256] device-mapper: ioctl: 4.29.0-ioctl (2014-10-28) initialised: dm-devel@redhat.com
[ 4.220274] Intel P-state driver initializing.
[ 4.220487] Consider also installing thermald for improved thermal control.
[ 4.220499] ledtrig-cpu: registered to indicate activity on CPUs
[ 4.220505] EFI Variables Facility v0.08 2004-May-17
[ 4.231092] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 4.243997] PCCT header not found.
[ 4.244076] TCP: cubic registered
[ 4.244151] NET: Registered protocol family 10
[ 4.244355] NET: Registered protocol family 17
[ 4.244370] Key type dns_resolver registered
[ 4.244750] Loading compiled-in X.509 certificates
[ 4.245430] Loaded X.509 cert 'Magrathea: Glacier signing key: 9b612381c2741f1dfdfe7d9e988abe985916702a'
[ 4.245442] registered taskstats version 1
[ 4.246981] Key type trusted registered
[ 4.250588] Key type encrypted registered
[ 4.250594] AppArmor: AppArmor sha1 policy hashing enabled
[ 4.250597] ima: No TPM chip found, activating TPM-bypass!
[ 4.250622] evm: HMAC attrs: 0x1
[ 4.251294] Magic number: 8:810:449
[ 4.251432] rtc_cmos 00:02: setting system clock to 2016-07-16 21:24:38 UTC (1468704278)
[ 4.251591] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 4.251592] EDD information not available.
[ 4.251661] PM: Hibernation image not present or could not be loaded.
[ 4.251980] Freeing unused kernel memory: 1412K (ffffffff81d27000 - ffffffff81e88000)
[ 4.251981] Write protecting the kernel read-only data: 12288k
[ 4.252268] Freeing unused kernel memory: 236K (ffff8800027c5000 - ffff880002800000)
[ 4.252376] Freeing unused kernel memory: 336K (ffff880002bac000 - ffff880002c00000)
[ 4.262784] systemd-udevd[154]: starting version 204
[ 4.272519] wmi: Mapper loaded
[ 4.279806] rtsx_pci 0000:0a:00.0: rtsx_pci_acquire_irq: pcr->msi_en = 1, pci->irq = 28
[ 4.280588] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 4.280593] r8169 0000:09:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 4.281493] [drm] Initialized drm 1.1.0 20060810
[ 4.282841] ahci 0000:00:1f.2: version 3.0
[ 4.282998] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[ 4.283016] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x10 impl SATA mode
[ 4.283018] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part ems apst
[ 4.284308] scsi host0: ahci
[ 4.285661] scsi host1: ahci
[ 4.285779] scsi host2: ahci
[ 4.285920] scsi host3: ahci
[ 4.286024] scsi host4: ahci
[ 4.286129] scsi host5: ahci
[ 4.286194] ata1: DUMMY
[ 4.286196] ata2: DUMMY
[ 4.286197] ata3: DUMMY
[ 4.286198] ata4: DUMMY
[ 4.286200] ata5: SATA max UDMA/133 abar m2048@0xd171b000 port 0xd171b300 irq 29
[ 4.286201] ata6: DUMMY
[ 4.287441] r8169 0000:09:00.0 eth0: RTL8168g/8111g at 0xffffc90010eb4000, f0:76:1c:ba:35:e6, XID 10900800 IRQ 30
[ 4.287443] r8169 0000:09:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 4.301515] [drm] Memory usable by graphics device = 2048M
[ 4.301518] checking generic (c0000000 7f0000) vs hw (c0000000 10000000)
[ 4.301519] fb: switching to inteldrmfb from EFI VGA
[ 4.301534] Console: switching to colour dummy device 80x25
[ 4.301610] [drm] Replacing VGA console driver
[ 4.303232] ACPI Warning: \_SB_.PCI0.GFX0._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[ 4.303265] ACPI Warning: \_SB_.PCI0.GFX0._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[ 4.303358] i915 0000:00:02.0: optimus capabilities: enabled, status dynamic power, hda bios codec supported
[ 4.303381] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[ 4.303403] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[ 4.303494] pci 0000:01:00.0: optimus capabilities: enabled, status dynamic power, hda bios codec supported
[ 4.303496] VGA switcheroo: detected Optimus DSM method \_SB_.PCI0.PEG0.PEGP handle
[ 4.303521] nouveau 0000:01:00.0: enabling device (0006 -> 0007)
[ 4.303540] ACPI Error: [AR02] Namespace lookup failure, AE_NOT_FOUND (20141107/psargs-359)
[ 4.303543] ACPI Error: Method parse/execution failed [\_SB_.PCI0.PEG0._PRT] (Node ffff8802568dea00), AE_NOT_FOUND (20141107/psparse-536)
[ 4.326463] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 4.326466] [drm] Driver supports precise vblank timestamp query.
[ 4.326592] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 4.439239] [Firmware Bug]: ACPI(PEGP) defines _DOD but not _DOS
[ 4.439554] ACPI: Video Device [PEGP] (multi-head: yes rom: yes post: no)
[ 4.439649] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:43/LNXVIDEO:00/input/input7
[ 4.440895] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 4.441009] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input8
[ 4.441091] [drm] Initialized i915 1.6.0 20141121 for 0000:00:02.0 on minor 0
[ 4.441325] nouveau [ DEVICE][0000:01:00.0] BOOT0 : 0x1171b0a2
[ 4.441328] nouveau [ DEVICE][0000:01:00.0] Chipset: GM107 (NV117)
[ 4.441329] nouveau [ DEVICE][0000:01:00.0] Family : NV110
[ 4.452997] nouveau [ VBIOS][0000:01:00.0] using image from ACPI
[ 4.453132] nouveau [ VBIOS][0000:01:00.0] BIT signature found
[ 4.453134] nouveau [ VBIOS][0000:01:00.0] version 82.07.7c.00.0c
[ 4.453934] nouveau [ DEVINIT][0000:01:00.0] adaptor not initialised
[ 4.453967] nouveau [ VBIOS][0000:01:00.0] running init tables
[ 4.490441] usb 3-1: new high-speed USB device number 2 using ehci-pci
[ 4.506480] usb 4-1: new high-speed USB device number 2 using ehci-pci
[ 4.510465] [drm] GMBUS [i915 gmbus vga] timed out, falling back to bit banging on pin 2
[ 4.527455] fbcon: inteldrmfb (fb0) is primary device
[ 4.527489] Console: switching to colour frame buffer device 240x67
[ 4.527525] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 4.527527] i915 0000:00:02.0: registered panic notifier
[ 4.560111] usb 1-6: new high-speed USB device number 2 using xhci_hcd
[ 4.560146] nouveau [ PMC][0000:01:00.0] MSI interrupts enabled
[ 4.560181] nouveau [ PFB][0000:01:00.0] RAM type: GDDR5
[ 4.560182] nouveau [ PFB][0000:01:00.0] RAM size: 2048 MiB
[ 4.560184] nouveau [ PFB][0000:01:00.0] ZCOMP: 0 tags
[ 4.560185] nouveau E[ PIBUS][0000:01:00.0] HUB0: 0x6013d4 0x00005702 (0x1f408200)
[ 4.560251] nouveau E[ PIBUS][0000:01:00.0] HUB0: 0x10ecc0 0xffffffff (0x1940822c)
[ 4.591324] nouveau [ PTHERM][0000:01:00.0] FAN control: none / external
[ 4.591330] nouveau [ PTHERM][0000:01:00.0] fan management: automatic
[ 4.591339] nouveau [ PTHERM][0000:01:00.0] internal sensor: yes
[ 4.591377] nouveau [ CLK][0000:01:00.0] 07: core 405 MHz memory 810 MHz
[ 4.591455] nouveau [ CLK][0000:01:00.0] 0a: core 270-1202 MHz memory 1600 MHz
[ 4.591553] nouveau [ CLK][0000:01:00.0] 0f: core 270-1202 MHz memory 5010 MHz
[ 4.591631] nouveau [ CLK][0000:01:00.0] --: core 405 MHz memory 810 MHz
[ 4.602535] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 4.603199] ata5.00: ATA-9: WDC WD10S21X-24R1BT0-SSHD-8GB, 03.01A02, max UDMA/133
[ 4.603201] ata5.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[ 4.603879] ata5.00: configured for UDMA/133
[ 4.604015] scsi 4:0:0:0: Direct-Access ATA WDC WD10S21X-24R 1A02 PQ: 0 ANSI: 5
[ 4.604269] sd 4:0:0:0: Attached scsi generic sg0 type 0
[ 4.604278] sd 4:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 4.604280] sd 4:0:0:0: [sda] 4096-byte physical blocks
[ 4.604412] sd 4:0:0:0: [sda] Write Protect is off
[ 4.604415] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.604483] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.606447] nouveau [ PGRAPH][0000:01:00.0] using external firmware
[ 4.606465] nouveau 0000:01:00.0: Direct firmware load for nouveau/nv117_fuc409c failed with error -2
[ 4.606471] nouveau 0000:01:00.0: Direct firmware load for nouveau/fuc409c failed with error -2
[ 4.606472] nouveau E[ PGRAPH][0000:01:00.0] failed to load fuc409c
[ 4.606488] vga_switcheroo: enabled
[ 4.606595] [TTM] Zone kernel: Available graphics memory: 4043032 kiB
[ 4.606597] [TTM] Zone dma32: Available graphics memory: 2097152 kiB
[ 4.606597] [TTM] Initializing pool allocator
[ 4.606601] [TTM] Initializing DMA pool allocator
[ 4.606607] nouveau [ DRM] VRAM: 2048 MiB
[ 4.606608] nouveau [ DRM] GART: 1048576 MiB
[ 4.606610] nouveau W[ DRM] Pointer to TMDS table invalid
[ 4.606617] nouveau [ DRM] DCB version 4.0
[ 4.606618] nouveau W[ DRM] Pointer to flat panel table invalid
[ 4.614200] nouveau E[ PFIFO][0000:01:00.0] unsupported engines 0x00000001
[ 4.614302] nouveau E[ DRM] failed to create kernel channel, -22
[ 4.623022] usb 3-1: New USB device found, idVendor=8087, idProduct=8008
[ 4.623025] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 4.623390] hub 3-1:1.0: USB hub found
[ 4.623479] hub 3-1:1.0: 6 ports detected
[ 4.626739] [drm] Initialized nouveau 1.2.1 20120801 for 0000:01:00.0 on minor 1
[ 4.638977] usb 4-1: New USB device found, idVendor=8087, idProduct=8000
[ 4.638980] usb 4-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 4.639266] hub 4-1:1.0: USB hub found
[ 4.639358] hub 4-1:1.0: 8 ports detected
[ 4.648780] sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13
[ 4.650094] sd 4:0:0:0: [sda] Attached SCSI disk
[ 4.791349] usb 1-6: New USB device found, idVendor=5986, idProduct=055e
[ 4.791352] usb 1-6: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 4.791353] usb 1-6: Product: Lenovo EasyCamera
[ 4.791355] usb 1-6: Manufacturer: Generic
[ 4.791356] usb 1-6: SerialNumber: 200901010001
[ 4.958788] usb 1-7: new full-speed USB device number 3 using xhci_hcd
[ 5.066856] tsc: Refined TSC clocksource calibration: 2594.013 MHz
[ 5.088072] usb 1-7: New USB device found, idVendor=8087, idProduct=07dc
[ 5.088075] usb 1-7: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.330772] input: DualPoint Stick as /devices/platform/i8042/serio1/input/input9
[ 5.344023] input: AlpsPS/2 ALPS DualPoint TouchPad as /devices/platform/i8042/serio1/input/input6
[ 6.067586] Switched to clocksource tsc
[ 6.247503] raid6: sse2x1 9062 MB/s
[ 6.315547] raid6: sse2x2 11360 MB/s
[ 6.383590] raid6: sse2x4 13105 MB/s
[ 6.451638] raid6: avx2x1 17492 MB/s
[ 6.519673] raid6: avx2x2 20113 MB/s
[ 6.587724] raid6: avx2x4 23479 MB/s
[ 6.587725] raid6: using algorithm avx2x4 (23479 MB/s)
[ 6.587726] raid6: using avx2x2 recovery algorithm
[ 6.588560] xor: automatically using best checksumming function:
[ 6.627741] avx : 28346.000 MB/sec
[ 6.636923] Btrfs loaded
[ 7.027711] EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null)
[ 7.671925] random: init urandom read with 117 bits of entropy available
[ 7.798269] random: nonblocking pool is initialized
[ 9.841823] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[ 9.841953] ACPI: \_SB_.PCI0.PEG0.PEGP: failed to evaluate _DSM
[ 9.841957] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[ 13.361244] EXT4-fs (sda9): re-mounted. Opts: errors=remount-ro
[ 13.388449] systemd-udevd[456]: starting version 204
[ 13.736517] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 13.736844] EDAC MC: Ver: 3.0.0
[ 13.738194] EDAC ie31200: No ECC support
[ 13.788455] input: Ideapad extra buttons as /devices/pci0000:00/0000:00:1f.0/PNP0C09:00/VPC2004:00/input/input10
[ 13.795018] cfg80211: Calling CRDA to update world regulatory domain
[ 13.797459] Bluetooth: Core ver 2.20
[ 13.797477] NET: Registered protocol family 31
[ 13.797478] Bluetooth: HCI device and connection manager initialized
[ 13.797481] Bluetooth: HCI socket layer initialized
[ 13.797484] Bluetooth: L2CAP socket layer initialized
[ 13.797488] Bluetooth: SCO socket layer initialized
[ 13.799396] Intel(R) Wireless WiFi driver for Linux, in-tree:
[ 13.799404] Copyright(c) 2003- 2014 Intel Corporation
[ 13.802757] usbcore: registered new interface driver btusb
[ 13.813001] lp: driver loaded but no devices found
[ 13.816156] Bluetooth: hci0: read Intel version: 370710010002030d00
[ 13.820341] AVX2 version of gcm_enc/dec engaged.
[ 13.820344] AES CTR mode by8 optimization enabled
[ 13.820913] ppdev: user-space parallel port driver
[ 13.845300] device-mapper: multipath: version 1.7.0 loaded
[ 13.850494] kvm: disabled by bios
[ 13.857475] intel_rapl: Found RAPL domain package
[ 13.857478] intel_rapl: Found RAPL domain core
[ 13.857480] intel_rapl: Found RAPL domain uncore
[ 13.857481] intel_rapl: Found RAPL domain dram
[ 13.857484] intel_rapl: RAPL package 0 domain package locked by BIOS
[ 13.873120] audit: type=1400 audit(1468697088.113:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=622 comm="apparmor_parser"
[ 13.873126] audit: type=1400 audit(1468697088.113:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=622 comm="apparmor_parser"
[ 13.873130] audit: type=1400 audit(1468697088.113:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=622 comm="apparmor_parser"
[ 13.873565] audit: type=1400 audit(1468697088.113:5): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=622 comm="apparmor_parser"
[ 13.873571] audit: type=1400 audit(1468697088.113:6): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=622 comm="apparmor_parser"
[ 13.873803] audit: type=1400 audit(1468697088.113:7): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=622 comm="apparmor_parser"
[ 13.881667] ACPI : EC: GPE storm detected(11 GPEs), transactions will use polling mode
[ 13.916980] kvm: disabled by bios
[ 13.994688] Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.7.10-fw-1.0.2.3.d.bseq
[ 14.007212] snd_hda_intel 0000:00:03.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[ 14.019434] sound hdaudioC1D0: autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[ 14.019436] sound hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 14.019438] sound hdaudioC1D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[ 14.019438] sound hdaudioC1D0: mono: mono_out=0x0
[ 14.019439] sound hdaudioC1D0: dig-out=0x1e/0x0
[ 14.019440] sound hdaudioC1D0: inputs:
[ 14.019441] sound hdaudioC1D0: Mic=0x19
[ 14.019442] sound hdaudioC1D0: Internal Mic=0x12
[ 14.059759] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input11
[ 14.059814] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input12
[ 14.099323] Bluetooth: hci0: Intel Bluetooth firmware patch completed and activated
[ 14.099736] input: HDA Intel HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input13
[ 14.099787] input: HDA Intel HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/sound/card0/input14
[ 14.099835] input: HDA Intel HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/sound/card0/input15
[ 14.143647] iwlwifi 0000:08:00.0: loaded firmware version 25.17.12.0 op_mode iwlmvm
[ 14.155678] iwlwifi 0000:08:00.0: Detected Intel(R) Dual Band Wireless AC 3160, REV=0x164
[ 14.155782] iwlwifi 0000:08:00.0: L1 Enabled - LTR Disabled
[ 14.156147] iwlwifi 0000:08:00.0: L1 Enabled - LTR Disabled
[ 14.210890] cfg80211: World regulatory domain updated:
[ 14.210899] cfg80211: DFS Master region: unset
[ 14.210900] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 14.210901] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[ 14.210902] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[ 14.210903] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm), (N/A)
[ 14.210904] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[ 14.210905] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[ 14.275795] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
[ 14.280886] media: Linux media interface: v0.10
[ 14.283567] Linux video capture interface: v2.00
[ 14.288875] uvcvideo: Found UVC 1.00 device Lenovo EasyCamera (5986:055e)
[ 14.291688] input: Lenovo EasyCamera as /devices/pci0000:00/0000:00:14.0/usb1/1-6/1-6:1.0/input/input16
[ 14.291736] usbcore: registered new interface driver uvcvideo
[ 14.291737] USB Video Class driver (1.1.1)
[ 15.183401] init: failsafe main process (817) killed by TERM signal
[ 15.719010] audit: type=1400 audit(1468697089.957:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/freshclam" pid=970 comm="apparmor_parser"
[ 15.719449] audit: type=1400 audit(1468697089.957:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cups-browsed" pid=972 comm="apparmor_parser"
[ 15.719890] audit: type=1400 audit(1468697089.957:10): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=967 comm="apparmor_parser"
[ 15.719897] audit: type=1400 audit(1468697089.957:11): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=967 comm="apparmor_parser"
[ 16.283011] init: cups main process (1198) killed by HUP signal
[ 16.283017] init: cups main process ended, respawning
[ 16.485342] Bluetooth: RFCOMM TTY layer initialized
[ 16.485347] Bluetooth: RFCOMM socket layer initialized
[ 16.485351] Bluetooth: RFCOMM ver 1.11
[ 17.110617] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 17.110626] Bluetooth: BNEP filters: protocol multicast
[ 17.110629] Bluetooth: BNEP socket layer initialized
[ 18.193297] iwlwifi 0000:08:00.0: L1 Enabled - LTR Disabled
[ 18.193664] iwlwifi 0000:08:00.0: L1 Enabled - LTR Disabled
[ 18.209389] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 18.289148] r8169 0000:09:00.0 eth0: link down
[ 18.289176] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.188355] init: samba-ad-dc main process (1453) terminated with status 1
[ 21.158131] nouveau E[ PIBUS][0000:01:00.0] HUB0: 0x6013d4 0xffffffff (0x1840822c)
[ 22.376405] nouveau [ PGRAPH][0000:01:00.0] using external firmware
[ 22.376424] nouveau 0000:01:00.0: Direct firmware load for nouveau/nv117_fuc409c failed with error -2
[ 22.376428] nouveau 0000:01:00.0: Direct firmware load for nouveau/fuc409c failed with error -2
[ 22.376429] nouveau E[ PGRAPH][0000:01:00.0] failed to load fuc409c
[ 22.563072] init: plymouth-upstart-bridge main process ended, respawning
[ 22.566179] init: plymouth-upstart-bridge main process (1613) terminated with status 1
[ 22.566185] init: plymouth-upstart-bridge main process ended, respawning
[ 25.079932] wlan0: authenticate with 68:a3:78:d6:78:50
[ 25.083290] wlan0: send auth to 68:a3:78:d6:78:50 (try 1/3)
[ 25.085087] wlan0: authenticated
[ 25.087191] wlan0: associate with 68:a3:78:d6:78:50 (try 1/3)
[ 25.091675] wlan0: RX AssocResp from 68:a3:78:d6:78:50 (capab=0x411 status=0 aid=1)
[ 25.092901] wlan0: associated
[ 25.092944] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 27.820945] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[ 27.821054] ACPI: \_SB_.PCI0.PEG0.PEGP: failed to evaluate _DSM
[ 27.821058] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[ 46.170762] audit_printk_skb: 153 callbacks suppressed
[ 46.170764] audit: type=1400 audit(1468697120.383:63): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=2700 comm="apparmor_parser"
[ 46.170769] audit: type=1400 audit(1468697120.383:64): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2700 comm="apparmor_parser"
[ 46.170989] audit: type=1400 audit(1468697120.383:65): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2700 comm="apparmor_parser"
Apparemment, c'est seulement la fin, car le début n'est plus visible...
Pour le ventilo, oui, il fait pas mal de bruit. Mais je me suis refusé à ouvrir le PC pour une histoire de garantie. Si les soucis ne sont pas résolubles, je le renverrais dans le pire des cas à la boîte qui me l'a vendu.
