En lisant les deux dernières pages et la première, j'ai pas bien compris si c'était seulement le WD Green (et red) ou/et les WD Caviar Green (et red).
Comme dans le titre c'est caviar, mais pas dans le premier post, que d'autre on le problème avec le caviar et que d'autres disent page d'avant qu'il n'y a pas de problème avec les caviar green, mais seulement le green (bas de gamme). Ou disent qu'autant passer au blue ou black. Mais caviar blue/ black ?
Comme je pensais acheter des Caviar Green 2To ou 1To pour de l'archivage et sauvegarde, qu'en est t-il ?
Pour voir si le disque est touché, il faut faire :
sudo smartctl -a /dev/sd*
Comme en DDinterne j'ai vérifié, j'ai un WD Green, sans Caviar depuis 2012. Allumé tous les jours toute la journée.
Le smartctl donne donc :
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-82-lowlatency] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: WDC WD10EZRX-00A8LB0
Serial Number: WD-WMC1U7648847
LU WWN Device Id: 5 0014ee 602eb8541
Firmware Version: 01.01A01
User Capacity: 1 000 204 886 016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Mon Oct 12 15:24:47 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (12840) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 147) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x30b5) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 134 130 021 Pre-fail Always - 4258
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1472
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 086 086 000 Old_age Always - 10591
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1472
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 99
193 Load_Cycle_Count 0x0032 130 130 000 Old_age Always - 211535
194 Temperature_Celsius 0x0022 116 107 000 Old_age Always - 27
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Est-ce qu'il a un problème ?
Et ensuite ? Appliquer le post #7 de Regression. Télécharger WDIDLE3 ? Par contre j'ai pas vu de Caviar Green dans leur liste. Et comment on exécute DOS pour le faire marcher ?
Désolé de reposer les mêmes questions.
